EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLEF378CBF Frigidaire Range - Instructions

All Instructions for the GLEF378CBF
61 - 75 of 325

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven fall on its front door and broke all the glass and the handle.
13 of 31 people found this instruction helpful.
  • Jonathan from Tiffin, OH
  • Easy
  • 30 - 60 mins
  • Screw drivers
First I removed all of the glass and broken parts. Next I placed the foil pieces on the back side of the glass. Next I put the glass into the slot. I then put the cap into place and then aligned the handle over it. With the help of another person, I inserted the screwed into the and saved us a lot of money that wback of the door (whic h is probably the hardest part) and tightened them. Everything looked great e would have spent on a new range.
Was this helpful?
Thank you for voting!
L.F. large burner element either on full hot or off. Would not cycle in and out with element control switch setting.
4 of 4 people found this instruction helpful.
  • Gerald from MADISON HTS, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it starte d but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.
Was this helpful?
Thank you for voting!
Burners getting too hot.
4 of 4 people found this instruction helpful.
  • Leslie from CONCORD, NC
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Watch video. This oven had the connecters that popped off and on which made this task easy.
Was this helpful?
Thank you for voting!
Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.
4 of 4 people found this instruction helpful.
  • Charles from OMAHA, NE
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p anel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.
Was this helpful?
Thank you for voting!
Right - front dual element not working.
4 of 5 people found this instruction helpful.
  • Douglas from VIRGINIA BCH, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clip s one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).
Was this helpful?
Thank you for voting!
replacing oven racks
4 of 5 people found this instruction helpful.
  • Lawrence from Elmira, NY
  • Really Easy
  • Less than 15 mins
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this helpful?
Thank you for voting!
Old racks had melted plastic on them.
4 of 5 people found this instruction helpful.
  • James from PAINESVILLE, OH
  • Very Easy
  • Less than 15 mins
It was a replace racks not repair. No problem
Was this helpful?
Thank you for voting!
Broken door glide
4 of 5 people found this instruction helpful.
  • Michael from Signal Hill, CA
  • Really Easy
  • Less than 15 mins
snapped the new piece of plastic in its place and ta da, its fixed.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people found this instruction helpful.
  • Alan from SAN MATEO, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Drawer Glide Was Broken
3 of 3 people found this instruction helpful.
  • Karen from Yuma, AZ
  • Very Easy
  • Less than 15 mins
Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.
Was this helpful?
Thank you for voting!
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
3 of 3 people found this instruction helpful.
  • Leota from AUXVASSE, MO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and M ama is happy!!
Was this helpful?
Thank you for voting!
Right rear burner not working properly
3 of 3 people found this instruction helpful.
  • Dante from SOUTHOLD, NY
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??
Was this helpful?
Thank you for voting!
Never received parts from PartSelect!!!
3 of 3 people found this instruction helpful.
  • Ralph from SULLIGENT, AL
  • Really Easy
  • 30 - 60 mins
It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!
Was this helpful?
Thank you for voting!
Lens cover for the oven light
3 of 4 people found this instruction helpful.
  • Larry from COZAD, NE
  • Really Easy
  • 30 - 60 mins
Very easy just had to pull the wire up that holds it secure.
Was this helpful?
Thank you for voting!
Change on e of the inside glass
4 of 7 people found this instruction helpful.
  • Ronald from Ozone Park, NY
  • Easy
  • 1- 2 hours
  • Screw drivers
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
Was this helpful?
Thank you for voting!
All Instructions for the GLEF378CBF
61 - 75 of 325