GFSL2KEYHLS General Electric Refrigerator - Instructions

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After wo ... Read more rking with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

Took the old filter out and put the new one in.
Easy Breezy!!

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They men ... Read more tioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

Removed screws on broken mullion at top and bottom. Save screws; you’ll need them. Disposed of broken mullion panel. The wires from plug had severed and were dangling at the bottom. Removed the plug inside small opening at bottom of door using needle nose pliers . Held new mullion up to left door, lining up screw holes at top. Screw ... Read more ed in top screw first. Pulled female part of plug out of small opening; removed male plug. Inserted new plug located on mullion in and pushed plug back into small opening. Installed one screw at bottom. The second screw at bottom wouldn’t line up so didn’t use. Installed second screw at top. The new mullion panel functions perfectly, seals well, and works great!

Replacement was easy. Once new board was installed I let run 24 hours and the compressor would not cycle off. Unplugged for 5 minutes then plugged back in to reset. Operates correctly now.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled al ... Read more l the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!

Needed a square head screw driver.
Appliance man wanted $80 to come out plus parts. Part cost $20 and took 10 minuyto out on. Had to empty half the refrigerator. That took longer than the time to fox

Took old one out with my fingers. Put new one in with my fingers.

I removed the top shelf and then the existing slide. I replaced the slide and then the shelves.

The only hitch was the need for a special screwdriver which cost $5.

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

Received new drawer, washed same, removed old drawer and transferred items to new drawer, THEN with out further ado reinstalled same!!! Wa La all finished.

My need for a part wasn't about an appliance repair, it was about making my GE frig work better for my particular needs. There is a lot of wasted space in the 2 door (French door?) model, at least for me anyway, and so when I discovered your company, online, just by googling, I jumped at the opportunity to buy an extra shelf to use t ... Read more he space more effectively. I was surprised. Package came quickly and installing it took a mere minute. I should have done this years ago! I am one happy camper. Excellent service, excellent quality shelf. Thank you everyone at PARTSELECT