- Home
- GDF520PSJ0SS
- Instructions
GDF520PSJ0SS General Electric Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
old gasket deteriorated, needing replaced
11 of 12 people
found this instruction helpful.
-
Brad from HIAWATHA, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Unscrewed brackets on top of dishwasher from underside of counter. Removed dress plate at bottom of dishwasher. Pulled dishwasher out of opening to access door hinge. Disconnected pulley cable/rope from each side door hinge. Let go slowly.
There is a 1/4 bolt holding the door tight to the hinge. With door closed (still) the screw is ... Read more on bottom of bottom edge. Use wrench to loosen and remove.
Once both bolts are out, open door. Pull door away from dishwasher just enough (1-3 inches) to slide out old gasket. Prior to removing take note of existing gasket orientation and installation. Slide old gasket out one side and slide new gasket in.
Push in door tight to hinges,close door, use wrench to put bolts back in. Reattach pulley cable/rope to each side. Push back into opening. Reattach to counter. Put dress plate on bottom back.
Return dishwasher to regular use.
There is a 1/4 bolt holding the door tight to the hinge. With door closed (still) the screw is ... Read more on bottom of bottom edge. Use wrench to loosen and remove.
Once both bolts are out, open door. Pull door away from dishwasher just enough (1-3 inches) to slide out old gasket. Prior to removing take note of existing gasket orientation and installation. Slide old gasket out one side and slide new gasket in.
Push in door tight to hinges,close door, use wrench to put bolts back in. Reattach pulley cable/rope to each side. Push back into opening. Reattach to counter. Put dress plate on bottom back.
Return dishwasher to regular use.
Read less
Was this helpful?
Thank you for voting!
Wouldn't start, no lighted functions.
15 of 25 people
found this instruction helpful.
-
Edward from BEAUFORT, SC
- Really Easy
- Less than 15 mins
-
Screw drivers
Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.
Was this helpful?
Thank you for voting!
Roller carrier got melted by heat coil
13 of 21 people
found this instruction helpful.
-
Dennis from CICERO, IN
- Very Easy
- Less than 15 mins
Replaced bad roller carrier with a new one.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud knocking. Sounds like plate banging against other plates or side of dish washer.
9 of 9 people
found this instruction helpful.
-
Montgomery from DELAFIELD, WI
- Very Easy
- Less than 15 mins
1) Pull out lower basket plate holder out. Now would be a good time to check roller wheels. 2) Grasp lower spray arm base (knurled collar on base) and turn counter clockwise to release. 3) Install new spray arm and turn knurled collar on base clockwise to lock it in. 4) Reinstall lower basket plate holder.
... Read more * Done *
... Read more * Done *
Read less
Was this helpful?
Thank you for voting!
Water Leaking from Bottom of Door
10 of 13 people
found this instruction helpful.
-
Evan from BEAUMONT, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
I fixed this issue by replacing the Dishwasher Tub Gasket (PS11774412) and the gasket on the bottom of the door (PS11700870). Replacing the tub gasket is very easy and straight forward. You just pull it off and put the new one on. The door gasket was much more complicated. See the steps required for replacement below:
The * ind ... Read more icates the part number in the diagram I am referencing
1. Remove the Toe Kick Assembly (*759)
2. Remove screws holding dishwasher to counter and pull the dishwasher out
3. With door shut, disengage the springs on both sides from the arm hinge assemblies *800 (I did this by taking the rope off the pulley hinge *734)
4. Disconnect the wire going from the dishwasher body to the door (there are two or three supports for the wire that need to be removed for it to come free)
5. Open the door about 15 degrees and pull the door upward (only one angle will work for removing the door)
6. Place the door on its front on the ground
7. Remove the two screws (*745) that hold one of the arm hinge assemblies to the door and pull the hinge away from the door (you don't need to pull it all of the way out)
8. Pull the old gasket out to the side and install the new gasket
The * ind ... Read more icates the part number in the diagram I am referencing
1. Remove the Toe Kick Assembly (*759)
2. Remove screws holding dishwasher to counter and pull the dishwasher out
3. With door shut, disengage the springs on both sides from the arm hinge assemblies *800 (I did this by taking the rope off the pulley hinge *734)
4. Disconnect the wire going from the dishwasher body to the door (there are two or three supports for the wire that need to be removed for it to come free)
5. Open the door about 15 degrees and pull the door upward (only one angle will work for removing the door)
6. Place the door on its front on the ground
7. Remove the two screws (*745) that hold one of the arm hinge assemblies to the door and pull the hinge away from the door (you don't need to pull it all of the way out)
8. Pull the old gasket out to the side and install the new gasket
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No water
9 of 11 people
found this instruction helpful.
-
Scott from FOUNTAINTOWN, IN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Turn off water supply, turn of power to dishwasher, remove mounting screws, slide dishwasher out of opening, place a pan under water supply valve, remove water line, remove screws holding the valve in place, disconnect electrical connector. Reverse process to install new valve.
Other Parts Used:
Was this helpful?
Thank you for voting!
Strange noise coming from the dishwasher, later a small leak appearing underneath
8 of 8 people
found this instruction helpful.
-
Donaldo from ALTADENA, CA
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with m
... Read more
etal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!
Read less
Was this helpful?
Thank you for voting!
Original spray arm got stuck under lower heater element and melted.
8 of 8 people
found this instruction helpful.
-
Kyle from WALLINGFORD, CT
- Very Easy
- Less than 15 mins
Removed old spray arm. Installed new one. New model spray arm doesn’t need metal heat shields.
Was this helpful?
Thank you for voting!
Replaced Lower Spray Arm for GE Dishwasher
9 of 11 people
found this instruction helpful.
-
Wendy from CHESAPEAKE, VA
- Very Easy
- Less than 15 mins
There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.
I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep ... Read more my old dishwasher working.
I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep ... Read more my old dishwasher working.
Read less
Was this helpful?
Thank you for voting!
Bad tub gasket
8 of 9 people
found this instruction helpful.
-
Larry from HAMBURG, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.
Was this helpful?
Thank you for voting!
dishwasher would not start
9 of 12 people
found this instruction helpful.
-
Missy from BOWDLE, SD
- Really Easy
- 15 - 30 mins
-
Screw drivers
I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had
... Read more
it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
tub gasket was damaged
8 of 9 people
found this instruction helpful.
-
Susan from STATEN ISLAND, NY
- Really Easy
- 15 - 30 mins
damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.I ... Read more t did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.I ... Read more t did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
Read less
Was this helpful?
Thank you for voting!
Pump would not drain tub
8 of 9 people
found this instruction helpful.
-
dennis from GRAHAM, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
Repair went fine, getting the right pump was the problem. I started with my local appliance parts house, they ordered part came in 3 days. Upon picking it up I noticed that the pump was shaped slightly different and the electrical hook up was totally different. Asking the parts guy what happened he said they must have sent the wrong pu
... Read more
mp. Returned it for credit and ordered it again. Four days later the same exact thing occurs. Parts guy credits my account and says better go directly to GE. Wait 10 days for GE, for this part and once again same odd looking pump with wrong electrical plug. My son who is a welder by trade asks me if there is a packet of parts in carton and yes there is. He says that perhaps there is a converter for the electrical. That was the solution no one told us that pump was universal and needed the adapter. Not even the 2 different tecks at first house. Perhaps that should be stated in the part would have saved us tons of time. Thanks D
Read less
Was this helpful?
Thank you for voting!
Dishwasher not heating/drying
8 of 10 people
found this instruction helpful.
-
Cynthia from LAUDERHILL, FL
- Easy
- 15 - 30 mins
-
Screw drivers
Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years)
... Read more
and everything else is fine. Just ordered the board so I really hope this fixes the problem.
Read less
Was this helpful?
Thank you for voting!
Dishwasher Would Not Drain
7 of 7 people
found this instruction helpful.
-
Steve from CHASKA, MN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the int
... Read more
ake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.
Read less
Was this helpful?
Thank you for voting!