GD1329LES2 LG Dryer - Instructions

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.

Watched a repair video. Very easy to replace, about an hour to repair.

I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the ... Read more dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.

Unscrewed the sensor cover, which on this model also holds the lint filter in plas. Then pulled the old sensors from their plug-ins. The new sensors easily slipped into the holder, and then replugged to the wires. The whole assembly screwed back into place. One note of caution: the flap where the filter slides in goes inside the cover, it ... Read more 's default is not upright, and be careful to not allow the inside spring for the cover to come off, or you might chase it!

Followed video provided on site

Removed the two screws holding the dryer door strike/locker assembly in place, removed the old and put the new in its place and replaced the screws.

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOT ... Read more OR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any su ... Read more ggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before workin ... Read more g on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

First, I set my laptop up in the laundry room, and went onto Youtube, searched LG dryer repair sensor install. then went step by step, pausing the video and starting it as I went. Then I Plugged it in and it worked. For $50 and some time I was able to do it, the prices from partselect are great and the turn around on shipping was super fa ... Read more st. Thank you Partselect. Kevin

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

My lg electric dryer would not heat up. I went on line and found that the thermostats (there are two) could cause this problem. I used my dvm to ohm out the thermostats and found that the high heat thermostat was open. I replaced this thermostat and the dryer ran for a little while and then quit heating. When I checked the high heat ... Read more thermostat again I found it to be open again. I then ordered and replaced both thermostats and the dryer has been working well since. The hardest part about this repair was the job of taking the dryer drum out to access the thermostats. I did however get good at doing this.

Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (t ... Read more o my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter ... Read more pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)