GCU23MITAFBB General Electric Refrigerator - Instructions

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

I took the part out of the package and placed it in the recessed water dispenser/ice maker cavity. Done!

To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid ... Read more in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

Water line 5/16inch was severed, under refrigerator. Used union connector to join line. Dispenser plate removed using allen key to unsnap plate ,from under the plate itself. Removed screws holding solenoid valve and removed the plug from circuit board connected to solenoid. Installed new solenoid valve. Put flapper back in place, and ma ... Read more de sure spring on left side of flapper is reattached to the opening on the flapper. This corrected all problems. Caution, keep an eye on spring that it remains in place.

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) ... Read more that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.

Removed front panel (using small screw driver) by popping it out, disconnected wire from solenoid, removed solenoid which was rusted, 3 small philip head screws held it in place insereted new solenoid,connected wire snapped front panel back in. Clapper valve closes tightly and no frost in frezzer, saved my self a bunch of money.

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it ... Read more couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

Our daughter spilled juice on the refrigerator light button. It started with the light coming on very slowly and then not at all. We popped off the old button with a flat head screwdriver, plugged in the new one. Works perfect. Can't believe how inexpensive and easy the fix was.

Removed tension spring, removed old lever, installed spring on lever, inserted lever in hole, re-attached spring to hook under front of refrigerator.

I removed and cleaned out the ice tray, then removed the ice auger. Next I had to remove the front cover of the tray that housed the crusher, this was done by removing to screws on the bottom and sliding the crusher section, once the crusher section was removed I simply slid off the crusher cover and replaced with the new one and put it ... Read more back together. It was that simple.

1. I unplugged the refrigerator/ freezer
2. Turned off water supply
3. Removed the screws that held the cardboard skirt in place
4. Unplugged the water tube from the push connect
5. Removed the screws around the water inlet to the ice maker
6. Remove the water fill tube
7. Install new water fill tube and put ... Read more all the screws and plates back where they go

unscrewed lamp and replaced it with new one!

I am a 64 year old woman.I will 65 in March. I do the plumbing and painting at our house and my husband who is 67 does the carpenter work, I help him by holding boards he is sawing etc. I though the job would be easier than it was, but it was still easy. I took out the first screw which was in plain sight, secound screw I could not get to ... Read more , and thought oh no I will have to take some other things apart. but when I removed the screw to the ice maker shield it was easy to slide it down out of way, and I got to 2nd screw pretty easy, I removed 2nd screw put new slide in place put screws in place started 1 st screw, then 2nd screw then went back and tightened 1st and 2nd screw, put the ic maker shield back in place tightened the screw slide ice bucket back in place, and though now this will be ready for company coming for the Holidays.... YEAH....