G2500PH (G 2500 PH 11944010) Karcher Pressure Washer - Parts

This spill valve is for pressure washers. Spill valve opens when water flowing through the pump gets too hot, releasing the hot water in exchange for cooler water.

This OEM Grooved Ring is a 12 x 20 x 4/6 rubber ring which can be installed with a screwdriver and wrench set. Installation is rated as "Medium" difficulty. It attaches in the cylinder head and is used to keep the oil in the pump from mixing with the water. If broken it will leak and must be replaced.

Genuine Karcher replacement part, it is sold individually. This part along with the piston controls the flow of water through the pump assembly. This part has a tendency to wear out. It may be wise to keep a few extra on hand.

Genuine Karcher replacement part, this item is sold individually. This part acts as a seal to keep the oil in the reservoir and the water in the pump form contaminating each other. It is installed on the piston.

This is a high-quality pressure spring that is made for use with Karcher pressure washers. It is an authentic item that is supplied from the original manufacturer. The spring applies tension on the piston that helps to create pressure inside the cylinder. Over time it may wear out, get damaged or lost eventually requiring a replacement to...Read more maintain your pump. Refer to the owners manual and the diagrams of your model for the correct installation. Note, this pressure spring is made of durable metal and is sold as an individual item. To perform this repair you will need a screwdriver and a wrench set. Remove the cover and the cylinder head to gain access to the pressure spring.

This is a genuine OEM sourced replacement part designed for use with Karcher pressure washers. It is the essential part of the unit allowing to direct and control the spray. This is a trigger gun with male m22 inlet and male m22 outlet. Please note the wand is sold separately. This pistol assembly is made out of plastic and metal. It is sold individually.

This high quality wheel and tire assembly is a genuine manufacturer sourced replacement part that is specially produced for Karcher pressure washers. It is the wheel that supports and helps to move your unit around. This part consists of a durable metal wheel with a rubber tire and it is sold individually, please note the hardware to secure it is sold separately.

It is an OEM item which is made for Karcher pressure washers. This component provides an air-tight seal for the pump housing. Over time the material will wear out and it may begin to crack eventually requiring a replacement to prevent leaks. To ensure the correct installation of the new gasket, refer to the appropriate diagrams of your sp...Read moreecific model. Note, it is made of a durable material and is sold as an individual component. You will need a socket set to take the pump housing apart in order to perform this repair.

This is a drain plug for different models of pressure washers. It is used to seal the check valve for the engine of the pressure washer and features an O-ring that can deteriorate over time. Failing to replace the drain plug can result in water leakage from the pump, potentially causing damage to the pump and surrounding parts, and leadin...Read moreg to pump overheating and seizing. To replace this drain plug, you will only need a few tools such as a screwdriver, Allen key, a set of pliers, and a utility knife. First, remove the pump from the pressure washer assembly using a screwdriver or Allen key. Then, disconnect the detergent hose by cutting it with a utility knife. Gain access to the valve(s), which may require you to use a screwdriver and/or hammer to remove the covering plate. Use a set of pliers to rotate and loosen the drain plug and remove it. Apply silicone grease to the new drain plug before installing and securing it. Reinstall the metal plate covering, reconnect the detergent hose to the pump, and reinstall the pump. Monitor your pressure washer for any leaks or other issues with the new drain plug installed.

It is a genuine OEM approved seal which is supplied for use with Karcher pressure washers. This replacement part is used to create and air-tight seal for the rotary shaft, over time the material may begin to deteriorate and crack eventually requiring replacement to maintain peak performance. It is made of durable rubber and it is sold individually.

This is a genuine item that is specially designed for use with Karcher pressure washers. It is supplied by the original equipment manufacturer. The oil helps to lubricate internal components of the pump to ensure it runs properly. Check the oil level regularly. Oil level should always be between the "FULL" and "ADD" level marks on the dip...Read morestick. Be sure the machine is level when checking the oil level. This will prevent them from wearing out. Refer to the owners manual of your model for the correct application of this oil. This synthetic 15W40 oil is sold in a single 1-liter container.

This rubber buffer is an authentic OEM component which is designed for use with Karcher pressure washers. It is attached to the bottom of the frame in order to provide support for the unit. Over time it may wear out, get damaged or lost eventually requiring a replacement. Make sure to refer to the diagrams of your model for the exact loca...Read moretion and the correct installation. One durable rubber buffer is included. Note, the bolt that secures this component is sold separately. Replacing this buffer is a simple task that should not require any tools. If your old part does not unscrew, you may use pliers to remove it.