FX730V-AS21 Kawasaki Engine - Parts

This is an original Kawasaki replacement part. The screw is designed by the manufacturer for use in trash pumps and engines. This part is made of metal, and is generally used in securing the ignition coil. You will require a screwdriver when replacing this item. This product is sold individually.

This is an authentic Kawasaki replacement part that has been sourced from the original manufacturer to be used four stroke engines. The filter is used to prevent dirt and debris from entering the engine's air intake. It is recommended to periodically replace the air filter to maintain the engine's performance. This item is sold as an individual replacement part.

This metal plate, is an authentic manufacturer replacement part used in outdoor power equipment as a part of the governor assembly. It is one of the two plates attached to the end of the camshaft which plays a key role in regulating the engine speed. When the engine speed increases or decreases, the plates are forced outward or inward, th...Read moreereby actuating the throttle and controlling the amount of air and fuel that enters the engine. This process allows the engine to maintain a consistent speed. If the plates become damaged or dislodged, you will notice fluctuating engine speed and poor load response. Before removing the plates, first disconnect the springs and linkage attached to them. Detach the plates from the camshaft and position the new ones in place.

This governor plate, also known as the governor control, is supplied by the original manufacturer for use in a variety of outdoor power equipment. It is a metal plate that works with the throttle linkage to allow the engine to maintain a consistent speed during operation. If the governor plate wears down or becomes damaged, you will notic...Read moree that the engine will stall under load, and the revolutions per minute (RPM) in your equipment will fluctuate, causing over-speeding or under-speeding as well as inconsistent power output, and performance. Therefore, it is critical to replace this part if it is no longer working, in order to continue operating your equipment. You can find the governor plate near the throttle linkage assembly in your equipment engine. Depending on your model, you may need to remove the air filter housing to access the plate. Disconnect the throttle linkage from the governor plate and remove the faulty governor plate. Place the new one in position, secure it with the appropriate fasteners, and reverse-assemble the rest of the engine components to complete your repair.

It is a genuine OEM sourced part that is specially designed for use with Kawasaki engines commonly installed on lawn and garden equipment. This item fits the opening in the crankcase helps to provide an air-tight seal to prevent any leaks. Over time seals tend to get compressed and may begin to crack eventually requiring replacements. It ...Read moreis made of durable rubber material and is sold individually. Refer to the appropriate diagrams for your model to ensure the correct repair procedure.

This flanged bolt is a genuine OEM steel fastener used to secure various components in outdoor power equipment. It features a flange base that acts as a built-in washer to distribute the load and prevent damage to the material it is fastened to. The bolt head has a diameter of 6mm, and the bolt shaft has a thread pitch of 20. The bolt can...Read more corrode and crack over time, or its threads may wear down, leading to loosening or detachment of the connected parts. You will likely note excessive noise, vibrations, and equipment instability. Inspect all the bolts in your equipment and replace those that are no longer functioning. Use a wrench or socket to loosen and remove the old bolt. Position the new bolt on the mounting surface and tighten it securely until the flange is flush against the surface. Each flanged bolt is sold individually.

This is an authentic Kawasaki replacement part. The air filter element is designed by the manufacturer for use in engines. This part is a plastic and metal casing with the filter material inside, and it is used to remove dust and debris from the air as it passes through the machine. You may require a wrench when replacing this part. This item is sold individually.

This is an original Kawasaki replacement part manufactured for use with four stroke engines. The special gasket is commonly used to seal the connection between the intake pipe and the cylinder. It is recommended to replace gaskets when servicing the engine to ensure proper seals when the parts are reassembled. This gasket is available as an individual replacement part.

The valve spring retainer goes between the spring and the collet. This part is made of metal and is available individually. It is an OEM from Kawasaki, Toro, and Lawn Boy for use in engines. A screwdriver, a socket set, and a wrench set might be helpful during the installation of this part. This item will need to be replaced if it breaks.

This is an authentic Kawasaki replacement part manufactured for use with small engines. The float valve is used to prevent fuel from entering the float bowl when it is full, then allows fuel into the bowl when the fuel is drained from the float bowl. This float valve is sold as an individual replacement part, please see model diagram for associative parts.