FX510BGSXAA Samsung Microwave Oven Combo - Parts

This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent use or food contamination, this burner can fail and will need to be replaced. If your burner is glowing red or orange, it is functioning as...Read more intended, but if your oven does not heat up properly, it likely needs replacement. This oven burner igniter is an OEM part that comes by itself and does not come with any of the screws necessary to secure it inside your oven.

This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor feature...Read mores a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.

The surface burner knob lets you control the heat of the surface burner on the range.

This surface burner cap is specially designed to fit with Samsung ranges. It is a genuine OEM replacement part supplied directly by Samsung to ensure compatibility. The burner cap is a round, black cap that has a diameter of approximately 1.75 inches. It covers the burner head and helps to distribute the flame across the burner to ensure ...Read moreyour food is cooked evenly. The cap also protects the burner head from accidental food spillage and debris to keep your range running efficiently. The burner cap will need to be replaced if it is cracked or can no longer remain securely attached to the burner head. Each cap is sold individually.

This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.

If a surface burner clicks but lights poorly or burns more strongly on one side, inspect the cap before replacing other components. A chipped, misplaced, or grease-covered cap can disturb the flame pattern. Lift it off only after the burner is off and cool, then clean and dry both mating surfaces. Also check the burner ports for debris wi...Read morethout enlarging the openings. If replacement is needed, use the complete range model and burner position to confirm fit. Set the cap level on its matching head before replacing the grate. Test the burner briefly, and turn it off at once if flames remain uneven or you smell gas.

This oven cavity floor coating or bottom floor panel is an authentic OEM part supplied by Samsung to ensure compatibility with various models of Samsung ranges. It is a protective layer that sits on the bottom surface of the oven cavity. It protects the bottom surface from direct contact with food particles and provides a smooth, easy-to-...Read moreclean surface that resists staining. The panel is also designed to reflect heat upwards, which helps to distribute heat throughout the oven cavity and ensures that your food is cooked evenly. You should replace this panel if it is damaged, corroded, or has excessive build-up that you are unable to remove.

This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside the oven. You can adjust its height using the multiple slots in the oven cavity to suit your cooking needs. Please keep in mind that this genuine OEM replacement part is sold individually.

The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.

This hexagon nut cap, also known as a nut cover cap, is a nylon-insulated cylindrical cap with left-hand threads and a 4mm thread size, for counterclockwise tightening. It is sourced from the original equipment manufacturer for use in ranges and microwave oven combos. The cap provides added security to prevent the hexagon nut that it rest...Read mores on from coming loose during operation and causing component instability. Over time it is normal for the hex nut cap to wear down, become damaged, or for its threads to become stripped. To replace a faulty nut cap, use a socket or wrench to unthread it from the hex nut. Place the new cap in its position and secure it in place to complete the repair. It is recommended to replace the fastener at the same time for extended durability.