FRSS2323AW Refrigerator - Instructions

Followed the online video from this site

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on e ... Read more ach side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the ... Read more slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

Removed old gasket and installed new one by pushing the gasket in the door groove.

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon be ... Read more gan to make aloud noise, due to there not being enough clerance.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to p ... Read more osition.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

The repair went easily after watching the video, took me less than an hour to complete the repair.

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something du ... Read more mb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

The repair was quick and easy. Just install the ordered bracket ( hinge ) on the top refrigerator door and cover. I had all the screws and cover but somehow the original bracket was missing...hummm

I first ordered the wrong switch I called and got a return label and was refunded my money before even shipping the wrong switch I was helped for the right switch and it arrived in 5 days the replacement works perfectly very easy to install. Thank you

First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacin ... Read more g the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.

i watched the video very simple repair

I followed the YTube video. The ice maker doesnot crush ice. The auger moves the ice to the dispenser. Is there a position for metal blades when assembling auger?