FREEZE Hotpoint Refrigerator - Instructions

Sears told me the part was no longer available. I came to your web site and then called your customer service. A very nice customer service lady helped me find the part. Very simple to pull the old one off and reinstall the new one with a rat trap behind the unit. Just in case it came back. Could have been a client but probably was a rat. ... Read more Thanks for the great service.

I watched some videos online trying to find one that pertained to my door gasket and found a couple. After that it was a snap. The old gasket came off easy and the new one went back on easy. I did however submerse it in hot water first to kind of even things out.

I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt s ... Read more pot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!

Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.

Both PartSelect and GE advisors told me to remove/loosen screws holding gasket to the door. This model has no screws. After pulling to old gasket from a corner (very difficult) I found that it is held in place by pressing it into a channel running around the door. Very difficult to line up the proper parts and very difficult to slide/adju ... Read more st it into place. When finally installed, one corner of the gasket protruded so that the door was not flush and actually kept the door from closing. I tried to push/pull it into place. No good. Finally I tried to hammer the gasket back to make it flush. No good, as it evidently crushed the magnets providing the necessary holding power and produced gaps. I finally had to get foam window stripping plus heavy duty magnets to pull door to frame. Result: door closes OK but some moisture collects around door.

take fan out,put new in

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems ... Read more that they all use the same switches. Very Very easy

Less than 5 minutes needed to remove cracked rail and replace with new rail. Must have a star wrench to perform task. Very simple task!

Manually snapped the plastic gasket into the slots of the refrigerator. The part fit perfectly after a slight adjustment.

I watched the video, supplied on the website, two times and followed the procedure. The repair was very easy and a pleasant experience. Lay the new gasket out flat for a couple of days in the sun prior to installation and remove the door and lay it flat for the installation of the gasket. Remove old gasket and clean track and surroundi ... Read more ng area thoroughly. Line up new gasket over track and at each corner and press into track, starting in center of one side, and work your way to each corner - repeat on each of the remaining three sides. Use a wet sponge to slide along the top of gasket while pressing same into track on the door.

Just snapped in.

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.