FLF337EWM Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
inner oven door glass broken
-
Cheryl from Derby, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.
Was this helpful?
Thank you for voting!
Broken oven door glass
-
Joseph from Cranberry township, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed directions for replacement of the glass from the web. Replacement was simple and easy.
Was this helpful?
Thank you for voting!
Clock/Oven program didn't work.
-
Julie from Doyle, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Very easy, just pulled the oven out and unscrewd the back, took the old program out plugged the new one in and it works just fine.
Was this helpful?
Thank you for voting!
broken inner glass
-
Neal from Warsaw, IN
- Easy
- 30 - 60 mins
-
Screw drivers
Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.
Was this helpful?
Thank you for voting!
Convert NGas to LP
-
Randall from Fernwood, ID
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The Conversion Kit was throughall with extra fittings and good instructions. My problem was haveing to pay a lisence gas installer $65.00 an hour to do a safety & pressure test. Maybee future Conversion kits would include a cheap disposable pressure tester with hose, then it would be a complete done job by the owner.
Was this helpful?
Thank you for voting!
bought a used gas range i have propane it was natural gas
-
Vernon from Moorehead, KY
- Easy
- 30 - 60 mins
-
Socket set
changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range
Was this helpful?
Thank you for voting!
Door glass cracked
-
Mike from Collegeville, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.
Was this helpful?
Thank you for voting!
inner glass door was broken
-
Norma J from Riverview, FL
- Difficult
- 30 - 60 mins
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process
... Read more
could then be reversed to assemble the parts and re assemble the door to the front of the range
Read less
Was this helpful?
Thank you for voting!
electronic temp controller went bad
-
david from reynoldsville, PA
- Easy
- 15 - 30 mins
-
Nutdriver
first unplug oven. then remove upper back panel(6 screws)with a 1/4 nut driver. next unplug electical connector from control unit. then remove unit by removing (4 screws on corners of unit with 1/4 nut driver. replace unit with new one and reassemble in reverse order.
Was this helpful?
Thank you for voting!
really bad ugly streaks inside of glass
-
John from Hemet, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door
... Read more
. Just reverse the way you take it apart to put it back together.
Read less
Was this helpful?
Thank you for voting!
inner glass uncleanable
-
Krista from Newtown, CT
- Easy
- 15 - 30 mins
-
Screw drivers
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this helpful?
Thank you for voting!
No heat from bottom or top element,k stove top and clock all worked fine.
-
steven from Daleville, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on
... Read more
the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Read less
Was this helpful?
Thank you for voting!
oven wouldn't work
-
Steve from Hiram, OH
- Easy
- 15 - 30 mins
-
Nutdriver
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven ba
... Read more
ck in. Done.
Read less
Was this helpful?
Thank you for voting!
no heat in oven
-
BARBARA from NORTH PORT, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this helpful?
Thank you for voting!
The Oven ignitor did not turn spark for the oven to turn on and heat up.
-
Ricardo from Brooklyn, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i
... Read more
was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)
Read less
Was this helpful?
Thank you for voting!