FLF337EUF Frigidaire Range - Instructions

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

the wrong parts list came with the stove, so the part I ordered didn't fit. The people at partselect were great to work with.

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

I just installed the extra rack and re-arranged the existing ones. Works great!

I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part ... Read more number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door ... Read more . Just reverse the way you take it apart to put it back together.

I replaced the oven control board. I used the old overlay because I could not find a model # but I was able to locate the exact replacement part. it took some to find, but it paided off.Thanks for your help. I Got the replacement part # from the old control board.

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but ... Read more it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i ... Read more was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on ... Read more the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven ba ... Read more ck in. Done.

first unplug oven. then remove upper back panel(6 screws)with a 1/4 nut driver. next unplug electical connector from control unit. then remove unit by removing (4 screws on corners of unit with 1/4 nut driver. replace unit with new one and reassemble in reverse order.