- Home
- FLF316WHSC
- Instructions
FLF316WHSC Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken inner oven door
1 of 3 people
found this instruction helpful.
-
Mary from Felts Mills, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necess
... Read more
ary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.
Read less
Was this helpful?
Thank you for voting!
Igniter lights up, but no flame appears, no gas
1 of 3 people
found this instruction helpful.
-
Denise from Clinton Township, MI
- Really Easy
- More than 2 hours
I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, w
... Read more
orked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,
Read less
Was this helpful?
Thank you for voting!
Oven And Broiler Wouldn't Light
0 of 1 people
found this instruction helpful.
-
DENNIS from HERKIMER, NY
- Difficult
- More than 2 hours
-
Screw drivers
The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.
Was this helpful?
Thank you for voting!
oven doesnt light at times
0 of 1 people
found this instruction helpful.
-
mike from temecula, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
had the gas company do a free inspection.he told me the igniters go bad over time,so i went online with my model #and found a symptom/remedy page at part select.it said replacing the igniter fixed the problem 100% of the time.that gave me confidence and i ordered it,installed it and fixed it for $53.00(the gasman said most plces charged $
... Read more
250-300 to fix it.i was proud of myself-1st ever oven repair=great job!!! thanks.
Read less
Was this helpful?
Thank you for voting!
needed 4 hands
0 of 1 people
found this instruction helpful.
-
Lois from Waretown, NJ
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
It went okay but I had to have some help putting it back together. One person held the glass while the other person tightened the screws.
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people
found this instruction helpful.
-
Randy from Crescent, IA
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Wrench (Adjustable)
Replacing the faulty ignitor would have been simple enough if my arms were a foot longer and the bolts that secured the old ignitor had not been baked on.
With an ample dose of WD40 and some Vise Grips I finally got them broke loose. An Ohm meter can tell you pretty quickly if the old ignitor is bad. My old ignitor measured m ... Read more ore than 1 mega ohm while the new ignitor read only about 346 ohms.
With an ample dose of WD40 and some Vise Grips I finally got them broke loose. An Ohm meter can tell you pretty quickly if the old ignitor is bad. My old ignitor measured m ... Read more ore than 1 mega ohm while the new ignitor read only about 346 ohms.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
Kenneth from Valencia, CA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
1st took out switch from thermostat unit, located right on the other side of where the temperature knob is located (that controls cooking temp of the oven). Had to lift up range cover to get to the thermostat. Tested this switch with a meter and found it was OK. This made me suspect the igniter, so I ordered one.
To install I fi ... Read more rst unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.
To install I fi ... Read more rst unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.
Read less
Was this helpful?
Thank you for voting!
Bake unit did not ignite
0 of 1 people
found this instruction helpful.
-
Joseph from Warminster, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.
Was this helpful?
Thank you for voting!
Oven wouldn't get hot..smell of gas
0 of 1 people
found this instruction helpful.
-
Eric from Chicago, IL
- Easy
- 15 - 30 mins
-
Wrench (Adjustable)
Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked gre
... Read more
at.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people
found this instruction helpful.
-
Steve from Canton, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.
to oven igniter, but igniter was not glowing.
Was this helpful?
Thank you for voting!
Would turn oven on, gas smell and would not light .
0 of 1 people
found this instruction helpful.
-
Michael from Forest City, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!
Was this helpful?
Thank you for voting!
oven was slow on lite up
0 of 1 people
found this instruction helpful.
-
BILLY from DUCKHILL, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed bottom plate in oven removed three screws and cut two wires.
Was this helpful?
Thank you for voting!
Oven igniter failure
0 of 1 people
found this instruction helpful.
-
Brett from Morgantown, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in
... Read more
oven, plug in and test.
Read less
Was this helpful?
Thank you for voting!
Oven door interior glass broken
0 of 1 people
found this instruction helpful.
-
TREVOR from NUTLEY, NJ
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the oven door screws, then I removed the outer handle and then there were 2 more sets of screws that actually held 2 panes of glass onto the door.
Was this helpful?
Thank you for voting!
Oven not igniting
0 of 1 people
found this instruction helpful.
-
Kirk from Saint Paul, MN
- Easy
- 15 - 30 mins
-
Wrench set
Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.
Was this helpful?
Thank you for voting!