FH3H2CDYV3 LG Washer - Instructions

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed f ... Read more rom the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

The bellows hose on the bottom of the tube had worn through where it flexed. This was an easy job except for the long reach you had to make under the washer to reach the hose clamps that held the part in place. These were spring loaded clamps which were easy to remove with pliers. I replaced them with ones that could be tightened with a s ... Read more ocket wrench since it was hard to replace the sprung clamps.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it rela ... Read more tively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG ... Read more PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under ... Read more the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

Basic skill

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the ... Read more two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the botto ... Read more m left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.