FH381V (AS21) Kawasaki Engine - Parts

This authentic part is supplied directly from the original equipment manufacturer for use with Kawasaki engines commonly installed on lawn and garden equipment. The float valve is used to allow fuel into the float chamber when the chamber has been drained and to stop fuel from entering the chamber when it is full. It provides an identical...Read more replacement for a missing or a faulty component that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality valve-float is made of durable metal and is sold individually.

This part is made of metal and is available as an individual replacement. The plate goes between the bracket and the fan. It will need to be replaced if it becomes broken or bent. When replacing this item a wrench may be needed. This is an authentic Kawasaki, Toro, and Lawn Boy replacement part that is sourced from the original manufacturer for use with 4 stroke engines.

This is a genuine OEM sourced replacement part that is specially produced for Kawasaki engines. Its purpose is to filter out dust and debris from contaminating the carburetor. One high quality pleated paper filter is included per order, please note the foam pre-filter is sold separately.

This is an authentic Kawasaki replacement part manufactured for use with small engines. The special snap ring is used to secure the piston pin to the piston. This snap ring is available as an individual replacement part, please see model diagram for associative parts.

A genuine item that is supplied directly from the original equipment manufacturer for use with Kawasaki engines commonly installed on lawn and garden equipment. It is a special component which is utilized to provide an air-tight seal for the crankcase, over time the material tends to wear out and it may begin to crack eventually requiring...Read more a replacement. Make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. This is a high-quality part which is made of durable rubber and is sold individually.

This item has been OEM sourced to ensure a high-quality standard. The gasket is an authentic Kawasaki part that is intended to be used with 4 stroke engines. The gasket is used to seal the connection between the carburetor and the air cleaner assembly. This gasket is sold as a single item.

This metal plate, is an authentic manufacturer replacement part used in outdoor power equipment as a part of the governor assembly. It is one of the two plates attached to the end of the camshaft which plays a key role in regulating the engine speed. When the engine speed increases or decreases, the plates are forced outward or inward, th...Read moreereby actuating the throttle and controlling the amount of air and fuel that enters the engine. This process allows the engine to maintain a consistent speed. If the plates become damaged or dislodged, you will notice fluctuating engine speed and poor load response. Before removing the plates, first disconnect the springs and linkage attached to them. Detach the plates from the camshaft and position the new ones in place.

This governor plate, also known as the governor control, is supplied by the original manufacturer for use in a variety of outdoor power equipment. It is a metal plate that works with the throttle linkage to allow the engine to maintain a consistent speed during operation. If the governor plate wears down or becomes damaged, you will notic...Read moree that the engine will stall under load, and the revolutions per minute (RPM) in your equipment will fluctuate, causing over-speeding or under-speeding as well as inconsistent power output, and performance. Therefore, it is critical to replace this part if it is no longer working, in order to continue operating your equipment. You can find the governor plate near the throttle linkage assembly in your equipment engine. Depending on your model, you may need to remove the air filter housing to access the plate. Disconnect the throttle linkage from the governor plate and remove the faulty governor plate. Place the new one in position, secure it with the appropriate fasteners, and reverse-assemble the rest of the engine components to complete your repair.

It is a genuine OEM sourced replacement part that is specially produced for use with Kawasaki engines commonly installed on lawn and garden equipment. This item fits the opening in the crankcase helps to provide an air tight seal to prevent any leaks. Over time seals tend to get compressed and may begin to deteriorate eventually requiring replacement. It is made of durable rubber material and it is sold individually.

This spring is an OEM direct from Kawasaki. The metal spring is compatible with many 4 stroke engines. This item provides the necessary resistance to the governor arm, and is sold individually. Pliers, wrench and a socket set are often needed for the repair process.