The Bottom Door Bin is also commonly known as a "cantilever shelf" is a clear plastic drawer which holds items in the bottom area of your fridge's interior, on the door. This OEM part is very easy to install and will not require any tools, you will just need to snap the mounting tabs into place for removal and installation. If damaged you...Read more will notice visible damage or have problems holding items in the fridge. If damaged, it should be replaced. Check your model number and user manual to see if this is the right part for you. This is important, as many fridges use multiple door bins, many of which vary slightly. This part is sold individually.
This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is a...Read moren easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your us...Read moreer manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.
This original equipment manufacturer Door Shelf is a white plastic part which holds items inside of your freezer or refrigerator door. It is roughly 10 inches long by 4 inches high by 5.5 inches wide. It can be used in the freezer or refrigerator and is very easy to repair. All you need to do is snap the new door bin into place, which req...Read moreuires no tools. This part is sold individually and not as part of a set, even though your refrigerator may take more than one of this part.
The function of the Refrigerator Water Inlet Valve (Triple Solenoid Water-Valve, Water Valve, Water Inlet Valve, Refrigerator Water Inlet Valve Assembly) is to release water from the supply line when activated, and send it through to your water dispenser or ice maker in your refrigerator. The water inlet valve is located at the back of th...Read moree refrigerator, and connects to the water supply. The valve can break from material fatigue or normal use. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. This valve measures approximately 7 inches long and 4.5 inches wide, and is constructed of plastic and metal. It comes in blue, and includes the valve and mounting bracket.
This genuine refrigerator door bin is perfect for storing items on your fridge door. Made from clear plastic, it’s easy to install with no tools required—just snap it into place. Ideal for replacing cracked or stained bins, it’s sold individually.
This genuine PureSource Ultra water filter will fit most Frigidaire french door and side by side refrigerators. You will find this filter located in the back, top right of the appliance. It is white in color and the filter has a polypropylene plastic housing and extruded carbon block filter media. Certified by NSF/ANSI to reduce contamina...Read morents that may be in your household water supply by 99.8 percent. The operating temperature for this filter is 33-100 degrees Fahrenheit, the flow rate is 0.5 GPM, the working pressure is 30-100 PSI, and it has a micron rating of 1. This filter should be replaced every six months or when the indicator lights up red. Installation is quick and easy. Push on the end face of the older filter to allow it to release. Remove and discard the old filter. Slide the new filter into the housing and press it down until it locks into place. Be sure to run water through the dispenser for about three minutes to prime the filter before use. Discard this water or use it to water plants. Do not forget to reset the indicator by pressing it down for 3-10 seconds. Review the use and care guide before you install for more detailed instructions.
This refrigerator shelf frame is an OEM part that serves to support the glass above your meat pan or chill drawer in your refrigerator. White to off-white in color, this part does NOT include the glass pane that it supports, you will need to order this part separately. This part is sold individually and measures close to 18.5x17.5 inches ...Read morein length and width. Most of our customers rated this repair as being very easy to carry out, taking less than 15 minutes and requiring no tools.
This manufacturer-approved air filter system for refrigerators eliminates odors and any impurities. It does this by neutralizing and removing odor-causing molecules. For best results, it is important to change the filter every 6 months to ensure that food is kept fresh, and the humidity is controlled. This part measures about 7 inches wid...Read moree and 5 inches deep. Follow installation instructions provided by the manufacturer when installing this part to ensure accurate results and further guidance. Remember to unplug the refrigerator from the power source before starting this project. The air filter may be located in different places depending on your appliance, but is usually on the inner right or left side. See your manual for exact location. Our customers rated this as a very easy repair that takes only a few minutes; just locate and remove the old air filter and insert the new one to complete the repair, which requires no tools.
This clear plastic crisper drawer is for side-by-side refrigerators. It is sold individually and sourced right from the original manufacturer. Please note that the new pan does not have the humidity control slide, and this component is now sold separately. The crisper drawer is designed to store produce at a humidity level that ensures yo...Read moreur food is kept fresh for as long as possible. It is commonly replaced because it is cracked, warped, or stained. For this simple tool-free repair, start by opening your refrigerator door and sliding out the old crisper drawer. Take your new crisper drawer and align the thin ridge on the top of the drawer with the track located inside the refrigerator. Slide the new part into place and your repair is complete.
If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and one heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of...Read more your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.
Cracked crisper glass? This replacement insert is just what you need. It’s about 17.12" by 15.40" and fits right into the frame above your crisper drawers, giving you extra shelf space and keeping things neat. Made of sturdy glass and easy to install—just slide the old one out and pop the new one in. Sold individually, so make sure it matches your fridge model before ordering!
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Darrell Callander - For model number FGHS2655PF5A
January 24, 2020
Had sy ef code and I replaced the evaporator fan. The the display on the door is not reading correctly. Some segments are not lighting up.
Hi Darrell. It sounds like it could be a bad power/control board. Part number PS10064937 and PS8689207. Thank you for your question and good luck with your repair.
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Jim - For model number FGHS2655PF5A
February 26, 2023
How do you repair a broken ice/water actuator lever?
Hello Jim, thank you for contacting us. According to our research, you may need to replace the actuator rod, part number PS1526549. We have also attached a video of a similar model to your refrigerator to help you replace the rod. Good luck with your repair!
Auto defrost problem! Replaced the thermostat and it still won't auto defrost. Is there a fuse in the system. If so where is it located? What else could be wrong! I've been defrosting it using the buttons on the front panel!
Hello Bob, thank you for your question. We have researched your model and found that the most likely fix for your problem is to replace the defrost heater part number PS2581596. If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Do you sell the control paned for this unit??? Some items light… others do not
Hello Bill, thank you for reaching out. The control panels compatible with your model are the user interface board, part number PS16555509, the electronic control board, part number PS10064937, and the power board, part number PS8689207. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
water leaking out of refrigerator
608 of 723 peoplefound this instruction helpful.
Jose from Alexandria, VA
Easy
15 - 30 mins
Nutdriver, Pliers, Wrench (Adjustable)
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the
... Read more valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
Read less
Was this helpful?
Thank you for voting!
Tab on bottom door bin broke off
541 of 573 peoplefound this instruction helpful.
Mark from Redlands, CA
Really Easy
Less than 15 mins
Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door.
My Orders
