FGFS36FWA Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not ignite
2 of 2 people
found this instruction helpful.
-
Joe from REAGAN, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I didn’t follow the instructions for the igniter
I simply jerked hard on the bottom drawer & it cam out onto the floor . Pulled range out & changed the oven sensor with a nut driver.
Same for the controller, 5 screws with a nut driver to remove back plate & 4 screws holding the controller in place , used the old face plate and ... Read more it was easy as pie
I simply jerked hard on the bottom drawer & it cam out onto the floor . Pulled range out & changed the oven sensor with a nut driver.
Same for the controller, 5 screws with a nut driver to remove back plate & 4 screws holding the controller in place , used the old face plate and ... Read more it was easy as pie
Read less
Was this helpful?
Thank you for voting!
Stove was dropped and had broken, bent frame and adjuster feet
2 of 2 people
found this instruction helpful.
-
Paul from PORT ORANGE, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this helpful?
Thank you for voting!
Igniter failed to ignite propane
2 of 2 people
found this instruction helpful.
-
Philip from FREDERICKSBRG, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.
Was this helpful?
Thank you for voting!
Low amperage to gas safety valve no gas flow.
2 of 3 people
found this instruction helpful.
-
RONALD from VIRGINIA BCH, VA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.
Was this helpful?
Thank you for voting!
Igniter gets hot but wouldn't ignite
2 of 3 people
found this instruction helpful.
-
Vajai from RICHMOND HILL, NY
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.
It was very self explationatry
Thank you parts select
I saved at least $400.
Was this helpful?
Thank you for voting!
oven wouldn't light consistently
2 of 3 people
found this instruction helpful.
-
BRADLEY from SHERIDAN, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble
Was this helpful?
Thank you for voting!
Took a long time to light oven, smell of gas, slow heat up.
2 of 3 people
found this instruction helpful.
-
Todd from OLYMPIA, WA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed whi
... Read more
ch has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!
Read less
Was this helpful?
Thank you for voting!
Lacking oven racks on used appliance
2 of 3 people
found this instruction helpful.
-
Katherine from Roanoke, VA
- Really Easy
- Less than 15 mins
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this helpful?
Thank you for voting!
panel behind the handle of the oven door was cracked
2 of 3 people
found this instruction helpful.
-
William from Ivyland, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Once I recieved the new part it was easy to determine what two screws to remove to remove both the panel and the handle. I removed the two screws, slid the panel up and removed it. The new panel locked into place when slid down over the door and I replaced the sctews.
Was this helpful?
Thank you for voting!
weak oven igniter/not enough amp. to light oven
3 of 6 people
found this instruction helpful.
-
JEFFREY from ULSTER, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver
first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arri
... Read more
ved early than anticipated.
Read less
Was this helpful?
Thank you for voting!
would not light oven
1 person
found this instruction helpful.
-
Richard from Huston, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard
Was this helpful?
Thank you for voting!
Oven would not come on, broiler worked and so did the burners
2 of 4 people
found this instruction helpful.
-
Jackie from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..
Thank You..
And re-connected the same way.
Peice of cake..
Thank You..
Was this helpful?
Thank you for voting!
oven would work intermittently
1 person
found this instruction helpful.
-
Michael from Chicago, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
Was this helpful?
Thank you for voting!
oven would not light
2 of 4 people
found this instruction helpful.
-
larry from 775, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
pulled drawer out and took old igniter off and replaced it
Was this helpful?
Thank you for voting!
Oven Would Not Light
1 person
found this instruction helpful.
-
Michael from Houston, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this helpful?
Thank you for voting!