FGF366DBD Frigidaire Range - Instructions

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since

1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through ... Read more the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the ... Read more wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!

remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.

Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .

First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--clo ... Read more se the door and call for heat the gas valve is working fine now....

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.

Very simple. I removed the oven racks, loosened the two screws that held the old panel in place, lifted out the old panel and replaced it with the new one, then tightened the screws to hold the new panel in place. It took no more than 10 minutes.

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install