- Home
- FGF358CGSB
- Instructions
FGF358CGSB Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken inside glass
1 person
found this instruction helpful.
-
ERIC from INDIANAPOLIS, IN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Followed your video and it was not hard at all
Was this helpful?
Thank you for voting!
interior oven door glass cracked
1 person
found this instruction helpful.
-
lois from middletown, DE
- Easy
- 1- 2 hours
-
Screw drivers
All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all
... Read more
pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.
Read less
Was this helpful?
Thank you for voting!
would not light oven
1 person
found this instruction helpful.
-
Richard from Huston, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard
Was this helpful?
Thank you for voting!
oven would not allow gas to flow for igniter to light
1 person
found this instruction helpful.
-
charles from bossier city, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
Was this helpful?
Thank you for voting!
Oven glows but won't ignite
1 person
found this instruction helpful.
-
John from MANASSAS, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Was this helpful?
Thank you for voting!
Longer time for oven to preheat. Replacing oven igniter solved my issue
1 person
found this instruction helpful.
-
Winfred from CARSON, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom c
... Read more
over, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.
Read less
Was this helpful?
Thank you for voting!
The inside glass window panel had cracked.
1 person
found this instruction helpful.
-
Patricia from Jacksonville, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back togethe
... Read more
r. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.
Read less
Was this helpful?
Thank you for voting!
Oven would not come on, broiler worked and so did the burners
2 of 4 people
found this instruction helpful.
-
Jackie from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..
Thank You..
And re-connected the same way.
Peice of cake..
Thank You..
Was this helpful?
Thank you for voting!
shatered inside oven glass panel
1 person
found this instruction helpful.
-
Vito from RED BANK, NJ
- Difficult
- 30 - 60 mins
-
Screw drivers
I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.
Was this helpful?
Thank you for voting!
GAS OVEN WON'T LIGHT.
1 person
found this instruction helpful.
-
stephen from LIVERPOOL, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER
... Read more
AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 person
found this instruction helpful.
-
JERRY L from PIPER CITY, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this helpful?
Thank you for voting!
my oven wouldn't light
1 person
found this instruction helpful.
-
david from granville summit, PA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done
Was this helpful?
Thank you for voting!
occasional failure to light-wife didn't trust it.
1 person
found this instruction helpful.
-
Carroll from Jackson, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed oven door. (two screws)
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped ol ... Read more d wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped ol ... Read more d wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat.
1 person
found this instruction helpful.
-
Jody from Storrs Manfield, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripp
... Read more
ed wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Read less
Was this helpful?
Thank you for voting!
Broken Broiler Door Handle
1 of 2 people
found this instruction helpful.
-
Sean from Scotch Plains, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
This product was super easy to apply. The part came in perfect condition and when I discovered 2 of the screws had fallen into the actual door (causing the door to apply pressure unevenly to the handle when pulled) fixing it was a snap.
Was this helpful?
Thank you for voting!