FGF355GWD Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I had a F31 code which means oven isn't working
1 of 3 people
found this instruction helpful.
-
Terry from CHELSEA, OK
- Really Easy
- Less than 15 mins
-
Nutdriver
Called fridgidaire and they told me the a F31 code means my temperature sensor is not working.
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people
found this instruction helpful.
-
Denise from Landover, MD
- Really Easy
- Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Lens cover for oven light broke.
0 of 1 people
found this instruction helpful.
-
Amy from Corona, CA
- Really Easy
- Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!
Two of theTop gas burners would not spark
0 of 2 people
found this instruction helpful.
-
Robert R from Lewistown, PA
- Easy
- Less than 15 mins
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Was this helpful?
Thank you for voting!
Broken globe in oven and burnt out light bulb
0 of 5 people
found this instruction helpful.
-
Sharon from Foley, AL
- Really Easy
- Less than 15 mins
Easy as 1-2-3
Other Parts Used:
Was this helpful?
Thank you for voting!
oven took too long to heat up
-
JAONNE from GAFILED, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!
Was this helpful?
Thank you for voting!
bake burner igniter open circuit--no oven heat
-
Earl from Trinidad, CO
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I followed the you tube www.partselect.com. Got door off--easy, and other parts off--easy, as you tube shows--I used the adj wrench to remove old screws--there are two--front one off--easy, the rear one was stripped at factory installation--so got it out, but broke it off in the process. So I had to drill out the part of the screw that re
... Read more
mained, and then used a substitute screw (8-32x1/2) on re-assembly. Re-assembly went easy--note that the removal of electrical connection is a "pinch-squeeze" to pull off.
Read less
Was this helpful?
Thank you for voting!
Oven would not turn on.
-
darwin from Wylie, TX
- A Bit Difficult
- 1- 2 hours
Gas stove worked, as well as brolier, but oven did not turn on at all. Replacing the bake igniter part did the trick. It is a simple operation, 30 minutes tops normally. In my case the screw was originally installed a little crooked and had caused it to strip and wouldn't come out. As a result, I had to also remove the gas pipe that the i
... Read more
gniter was attached to in order to forcibly remove the screw and detach the old bake igniter. This is what caused the extra time and difficulty.
Read less
Was this helpful?
Thank you for voting!
Men Should Not Use The Oven
-
David from Suttons Bay, MI
- Really Easy
- Less than 15 mins
Delivery was fast. Two screws to remove the old oven panel. Slipped in the new panel and tightened the screws with my fingers. Job completed. It was as easy as that.
Was this helpful?
Thank you for voting!
Sliced Outlet Cord
-
William from Saint Clair Shores, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part
... Read more
number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Read less
Was this helpful?
Thank you for voting!
Aluminium foil fused to the panel
-
James from Durham, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the two back screws, slid out the old panel, then fitted in the new panel (it fit perfectly) and replaced the screws. Five minutes, tops.
Was this helpful?
Thank you for voting!
oven would not stay on
-
Mark from AuGres, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
remove belly pan ,pull draw out easy acsess remove screws and replace
Was this helpful?
Thank you for voting!
replace lower oven floor
-
ed from petaluma, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
removded 2 screws at rear of panel, moved panel toward rear of oven, lifted up and out. Slid in new panel in front groove then lowered onto oven floor and secured it with the 2 screws at rear of oven.
Was this helpful?
Thank you for voting!
no heat
-
John M. from PLEASANT PRAIRIE, WI
- Easy
- Less than 15 mins
-
Nutdriver
Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....
Was this helpful?
Thank you for voting!
Needed to install an anti-tip bracket on my stove.
-
Daniel from Provo, UT
- Really Easy
- Less than 15 mins
-
Socket set
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this helpful?
Thank you for voting!