FGF348KSC Frigidaire Range - Instructions

YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made i ... Read more t more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

The electric was the next step it worked.

replaced it

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to joi ... Read more n the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try Pa ... Read more rtSelect for Cub Cadet and Yamaha OB parts. Thanks. John

Removed outer glass first ,then worked my way thru to inner glass..

Very easy, just pulled the oven out and unscrewd the back, took the old program out plugged the new one in and it works just fine.

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, yo ... Read more u can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

The Conversion Kit was throughall with extra fittings and good instructions. My problem was haveing to pay a lisence gas installer $65.00 an hour to do a safety & pressure test. Maybee future Conversion kits would include a cheap disposable pressure tester with hose, then it would be a complete done job by the owner.

changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

1. Remove the old Trim by opening the door and unscrewing the two top screws holding the trim and glass to the door. 2. Lift the trim piece off of the glass, being careful as the glass will be a bit loose, and unscrew the handle from the trim piece, discard those two screws. 3. Place the new trim piece on the glass so that it fits snugly. ... Read more 4. Place the screws back through the holes on the inside of the door, through the new trim piece and attach them to the handle. 5. Tighten down snugly and close door. You are done!