EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FGF337ABL Frigidaire Range - Instructions

All Instructions for the FGF337ABL
106 - 120 of 332

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The ignitor came on with a call for heat but the gas valve did not open
1 person found this instruction helpful.
  • Terry from Tonganoxie, KS
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--clo se the door and call for heat the gas valve is working fine now....
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 4 people found this instruction helpful.
  • M. Nicole from La Mirada, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!
Was this helpful?
Thank you for voting!
Oven wouldn't light off
1 person found this instruction helpful.
  • Mickey from Fallbrook, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.
Was this helpful?
Thank you for voting!
No problem
1 person found this instruction helpful.
  • Pamela from DETROIT, MI
  • Very Easy
  • Less than 15 mins
  • Screw drivers
My daughter did the installation and it was quick. She had no problem, and it's working great. She love it. She just use a philp screwdriver to take off the bolt then unplug the control adaptor. From the back then plug the new one in and that's it. Easy as 123
Was this helpful?
Thank you for voting!
OVEN WOULD NOT COME ON
1 person found this instruction helpful.
  • david from SLIDELL, LA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Was this helpful?
Thank you for voting!
oven would not lite
1 person found this instruction helpful.
  • david from canastota, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite
Was this helpful?
Thank you for voting!
Code f10
1 person found this instruction helpful.
  • bennie from san francisco, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Easy installation using a nut driver and a Phillip screwdriver.plug in harness connector and done.
Was this helpful?
Thank you for voting!
Needed an additional rack
1 person found this instruction helpful.
  • Gary from Darragh, PA
  • Really Easy
  • Less than 15 mins
Open the door and slide in the new rack.
Was this helpful?
Thank you for voting!
Longer time for oven to preheat. Replacing oven igniter solved my issue
1 person found this instruction helpful.
  • Winfred from CARSON, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom c over, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 person found this instruction helpful.
  • JERRY L from PIPER CITY, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this helpful?
Thank you for voting!
Oven would not light
1 person found this instruction helpful.
  • Stephen from Pittsburgh, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
Was this helpful?
Thank you for voting!
replaced theoriginal power cord.
1 person found this instruction helpful.
  • Blanca from Union City, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this helpful?
Thank you for voting!
GAS OVEN WON'T LIGHT.
1 person found this instruction helpful.
  • stephen from LIVERPOOL, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.
Was this helpful?
Thank you for voting!
Oven glows but won't ignite
1 person found this instruction helpful.
  • John from MANASSAS, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Was this helpful?
Thank you for voting!
The range clock wasn't keeping time, and the oven would shut off randomly in the middle of baking.
1 person found this instruction helpful.
  • Andrew from San Juan Capistrano, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed the metal cover on the back of the range by unscrewing the square-drive screws around the perimeter, left the center screw until the end to make it easier to hold for removal.

The control unit was held in with 4 Philips head screws, and connected by a single wire-to-board connector. Unplugged the connector and removed t he screws and the control unit came right out.

The replacement unit doesn't come with a face plate, so I used a razor blade to carefully remove it from my old unit. The adhesive that held it on was still sticky so I was able to easily attach it to the new unit.

Then I just put everything back together in reverse order. One of the easiest appliance prepares I've done.
Was this helpful?
Thank you for voting!
All Instructions for the FGF337ABL
106 - 120 of 332