FGF328GSF Frigidaire Range - Instructions

We turned off the gas, moved the stove out from the wall and unplugged it. Then we removed the metal back (using an adjustable wrench because we didn't have a square headed screwdriver.) We then removed the four screws that had held the clock/timer in place before the plastic shattered. We inserted the new part and reinserted the screw ... Read more s. Then we replaced the back cover. When we plugged the range back in and set the clock everything worked beautifully.

Bought a electric range/oven with a broken glass in the door cheaply because the owner didn't think they could fix the glass. I watched the video on You Tube on how to handle the spring loaded hinges and followed the steps as presented. The toughest part of the job was cleaning all the crud on all of the glass due to the gap in the inne ... Read more r glass. I had to use a square drive and a phillips head screwdriver to disassemble and reassemble the door. It took less than 30 minutes to complete the job and most of that time was cleaning the glass.

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but ... Read more it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i ... Read more was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, yo ... Read more u can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

I replaced the oven control board. I used the old overlay because I could not find a model # but I was able to locate the exact replacement part. it took some to find, but it paided off.Thanks for your help. I Got the replacement part # from the old control board.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on ... Read more the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

I got the ex husband to come over and take it apart and fix it, he said that it was a really easy repair to complete.

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as t ... Read more his prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven ba ... Read more ck in. Done.

Removed the door and carefully dismantled all of the layers. In my particular situation, I needed to do some high heat painting as over the years the white panels had discolored due to heat. So, I had to wait a day or so for the painted panels to dry--but they looked great when done. Some words of caution, really look the diagrams over ... Read more and be sure you are ordering the correct glass (there are three and all different). I initially ordered the wrong one but used it anyway as it replaced a badly stained one. But, I had to re-order the correct glass. It was amazing how quickly I got both orders, though. Only took a couple of days!! So, am very pleased with the way it looks--like new again and quite easy if done systematically!