FGF303CWH Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One burner had broken
3 of 5 people
found this instruction helpful.
-
Clarence from Bronx, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I put in the part and it went well, I have used other parts from your factory for the same stove so I knew it was going to go easy. The part only required one screw.
Was this helpful?
Thank you for voting!
Stove was dropped and had broken, bent frame and adjuster feet
2 of 2 people
found this instruction helpful.
-
Paul from PORT ORANGE, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this helpful?
Thank you for voting!
Oven stopped heating all together when turned on.
2 of 2 people
found this instruction helpful.
-
Jalen from GREENWOOD, IN
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
removed racking, flame cover, and wire plug in cover by pulling out racking, removing one nut, and one screw for the cover. Removed two small bolts to remove igniter, and then unplugged from two locations. Did the same in reverse for install.
Was this helpful?
Thank you for voting!
Igniter wouldn't glow and obviously no heat
2 of 2 people
found this instruction helpful.
-
David from JERSEY CITY, NJ
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Partselect always have their install video with the parts they sell so it was easy. I know contractors must not be happy with people like partselect and YouTube with all the instructional videos they supply us with. Keep up the great work partselect.
Was this helpful?
Thank you for voting!
Igniter failed to ignite propane
2 of 2 people
found this instruction helpful.
-
Philip from FREDERICKSBRG, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.
Was this helpful?
Thank you for voting!
oven wouldn't light consistently
2 of 3 people
found this instruction helpful.
-
BRADLEY from SHERIDAN, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble
Was this helpful?
Thank you for voting!
Oven would come on when turned off
2 of 3 people
found this instruction helpful.
-
Joy from ANDERSON, IN
- Really Easy
- 15 - 30 mins
-
Screw drivers
It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.
Was this helpful?
Thank you for voting!
Low amperage to gas safety valve no gas flow.
2 of 3 people
found this instruction helpful.
-
RONALD from VIRGINIA BCH, VA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.
Was this helpful?
Thank you for voting!
Igniter gets hot but wouldn't ignite
2 of 3 people
found this instruction helpful.
-
Vajai from RICHMOND HILL, NY
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.
It was very self explationatry
Thank you parts select
I saved at least $400.
Was this helpful?
Thank you for voting!
Lacking oven racks on used appliance
2 of 3 people
found this instruction helpful.
-
Katherine from Roanoke, VA
- Really Easy
- Less than 15 mins
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this helpful?
Thank you for voting!
Needed an additional rack
1 person
found this instruction helpful.
-
Gary from Darragh, PA
- Really Easy
- Less than 15 mins
Open the door and slide in the new rack.
Was this helpful?
Thank you for voting!
Had to go from nat gas to lp
1 person
found this instruction helpful.
-
Tom from Wappapello, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Replaced uper orifice n adjusted oven as instructed.
Was this helpful?
Thank you for voting!
replaced theoriginal power cord.
1 person
found this instruction helpful.
-
Blanca from Union City, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this helpful?
Thank you for voting!
Gas oven stopped working. I read that it probably was the igniter. Bought a new one to ins
1 person
found this instruction helpful.
-
Dennis from WEST ROXBURY, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made i
... Read more
t more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.
Read less
Was this helpful?
Thank you for voting!
Wood Burning Oven
1 person
found this instruction helpful.
-
Thomas from YAMHILL, OR
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
The Appliance light was installed in a wood burning oven used by a commercial bakery. The entirely masonry oven is used to cook a specialty product with origins in Brazil.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodat ... Read more e the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodat ... Read more e the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
Read less
Was this helpful?
Thank you for voting!