FFVU17F2SC0 Frigidaire Freezer - Instructions

Unscrew it off and screw the other on

Removed the top hinge, took the door off ,swapped out the new parts

The old defrost timer started making a screeching noise (probably bearings going out). The replacement part was a cinch to install. When I initially spoke to a PartsSelect person, they said the part number I gave them was not consistent with my old '94 Tappan Freezer. They were able to still find the proper replacement part number. Th ... Read more e video that was on-line helpful also.

Turned freezer off and removed cover in freezer at the bottom, notice fan blades were broken off, removed the 2 screws that were holding the fan motor in place removed fan blade and replaced with new fan blade, problem solved

Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. ... Read more Works like a champ again!

This unit already had an area where an extra shelf would go. Just put in into the extra shelf holes. No problems.

I recommend completing steps 1-3 before purchasing your part, so as to avoid my mistakes.

1) Unplug the freezer and clear whatever is currently in the door. This fix is fast enough you don't need to empty the whole freezer.

2) Use a socket wrench to remove the two bolts holding the top hinge to the freezer. Once they ... Read more 're off, the hinge can pulled up and off.

3) Lift the door free from the bottom hinge. Important Note! Check that it's the door closing cam that's broken, and not, for example, the bearing that seats with the door cam that is listed on the freezer part of the schematic, and not the door part. If you're a smarty pants, you order(ed) the right part. If you're me, you continue with this tutorial but still need to order another part to complete the fix. Don't be like me.

4) Using your philips-head screwdriver, remove the screw holding the remnants of the old door cam to the bottom of the door. Pull out the old cam and insert the new one. Rescrew.

5) Grab your extra person put of your toolbox and have them help you guide the door back onto the bottom hinge. The door is not heavy but no one wants to play blind Battleship while your freezer contents actively defrost.

6) Stick the top hinge back into place and reattach the bolts.

7) PLUG YOUR FREEZER BACK IN! And also check that the door works now.

Shelf went right in required holes.

The timer in this older unit is clearly exposed at the back of the freezer underneath the freezer compartment. It is attached with two Phillips head screws. After the screws are removed, the timer can be unplugged and the new one plugged in. The new timer has an extra flange to allow it to be used on more than one model of freezer. In ... Read more order to mount the timer in this unit, you have to remove the extra flange by carefully cutting it away from the timer body, in similar fashion to what's depicted in the online video. This will allow you to mount the new timer to the mounting plate using the two screws from the old timer.

-got friend
-got step stool
-removed upper hing w/3/8 nut driver
-lifted door vertically off of lower hing pin (w/friend)
-removed and replaced broken nylon washer
-lifted door back onto lower pin hing hole
-while friend holds door reinstall upper hing bracket with 3/8 nut driver
-had cup of coffee

Removing the old one took longer than installing the new seal...its a one person job bit my son helped me..

First unplug freezer, then disconnected wires from timer.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated ... Read more defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.