FFU17F5HWS Frigidaire Freezer - Instructions

there was no voltage to compressor but line voltage coming in checked compressor according to your video it checked out good.checked heater and thermistor also they checkedout good.but control board was flashing but could not be set so I replaced it .new board solved problem power surge must have taken control board out . freezer now p ... Read more lugged into surge protector.

I order another one thanks

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though ... Read more it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Unplug freezer.
Open freezer and Remove the bottom 2 shelves and drawers.
Remove 6 screws (Phillips) securing the inside access panel located in the back of the unit.
Locate the defroster bar which is secured to the bottom of the condenser radiator. Trace the cable to the thermostat that is clipped into the condenser coi ... Read more l.
Unplug thermostat power cable located at the top left of the condenser coil, and the defroster bar cable on the upper right.
Release metal band that secures bar to the coil at the bottom where the coil and bar are secured.
Reverse for installation.

I did watch a repair a utube video which I asked for when ordering. Pretty much followed most of the directions but:

started in left corner an lossed all screws from left to right. took off old gasket in small sections and inserted the new gasket and semi tighten screws

proceeded down left side then right little by l ... Read more ittle as above. to get to bottom of door.

bottom corners were a little snug to get them into place. the last corner was snug but once connected. tighten screws not too tight. You dont want to strip them.

test door with piece of paper.

if paper is not a snug tug, you can adjust gasket with a hair dryer set to low.

it was easy. freezer is all set.

Partselect was great to deal with, support verified the part number was correct for my freezer and help with that video.

After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced perso ... Read more n may have more of problem with this type of "repair".

Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. ... Read more Works like a champ again!

This did not fix the problem. Call a repairman and he cannot come until 9/11. Food is staying frozen. Alarm sounds for awhile and then shuts off for a bit.

My freezer is back working fine, Thank You

Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on.
Reattach back panel. Put shelves back in.

The left swing hinge (297283901) that i needed is not available anywhere so I bought the right swing hinge (297283900), used a hydraulic press to pop out the pin and move it to the other hole. After that it was real quick to remove the screws and change out the hinge, changing the swing of the door. It is easiest to remove the top hinge ... Read more and door first when doing this.

UNPLUG POWER CORG
PULL OUT BAD CONTROL UNIT
PLUG IN NEW CONTROL .
PLUG POWER CORD.
FREEZER STARTED UP WORKS PERFECT.
COULD NOT BE EASER.

No repair. The key fit!

Using my fingernails, I pried/popped out the panel. Replaced it with the new one. Popped right in!! No wires to fool with or anything!

We are not handy, we had an appliance repair person install the gasket.