FFU17C4CW2 Frigidaire Freezer - Instructions

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the cop ... Read more per refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

I order another one thanks

Used a ??. The repair was easy took less than 5 minutes

I removed the top and bottom plastic bits that hide the screws. Then I removed the screws and put the new handle on with the same sheet-metal screws. No problems encountered.

It was almost too easy. All I had to do was screw 4 screws into the handle, put the caps on to hide the screws and I was done. And I saved money by ordering from Frigidaire vs my local appliance store where I actually purchased the freezer.

Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.

I did watch a repair a utube video which I asked for when ordering. Pretty much followed most of the directions but:

started in left corner an lossed all screws from left to right. took off old gasket in small sections and inserted the new gasket and semi tighten screws

proceeded down left side then right little by l ... Read more ittle as above. to get to bottom of door.

bottom corners were a little snug to get them into place. the last corner was snug but once connected. tighten screws not too tight. You dont want to strip them.

test door with piece of paper.

if paper is not a snug tug, you can adjust gasket with a hair dryer set to low.

it was easy. freezer is all set.

Partselect was great to deal with, support verified the part number was correct for my freezer and help with that video.

After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced perso ... Read more n may have more of problem with this type of "repair".

removed 4 screws-replaced handle-very easy-worked great

removed two pieces of trim.....removed four screws of old handle.....replaced with new handle....replaced screws.....replaced trim pieces

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other p ... Read more arts, but not happy that the actual part I needed was not available - had to use other methods.

This did not fix the problem. Call a repairman and he cannot come until 9/11. Food is staying frozen. Alarm sounds for awhile and then shuts off for a bit.

Was able to order the handle and screw it on the refrigerator using the screws from the original handle in about 10 to 15 minutes.

Very simple - removed the plates that cover the end of the handel, then removed the screws and the broken handle. There were four screws - did a top one, then a bottom one, then the other top and bottom one. Made sure they were on tight and put the covers back on. Really proud of myself!

Using the socket wrench, I removed the old element from the oven wall attached by two hexagonal screws. I then removed the electrical attachment to the oven using a Philips head screw driver. Replaced the element with the new one and reversed the process. The oven works like new!