FFU14M2AW0 Frigidaire Freezer - Instructions

its best to use power screw driver lot of screws .took out all screws took off door took out side to remove ice from door. just used water to melt ice. took off old gasket and put on new gasket. put door in place and started screws in four coners do not tighten screws at this point.put in rest of screws. work arondclock wise making sure g ... Read more asket is seated while tighing screws. check gasket for flatness you may have to use hair dryer on gasket to make it flat.

Simply unscrew panel but do not remove it. Remove old gasket. Fit new gasket between panel and door. Fasten screws and no more leaks and better temperature contol. This was so easy and rejuvenated my freezer. Thank you for quick shipment, great service, easy to navigate website, and fast phone help. I highly recommend your company. good l ... Read more uck with your repairs that you can do, as I have zero mechanical ability and did it !!!!

After building a test box and determining the Controller was bad simply ordered parts and installed. Installation was a little difficult due to locking spades on electrical connections.

Unplug all power from freezer. Remove Bail wire from controller capacitor unit and remove from compressor by pulling STRAIGHT from compre ... Read more ssor body to avoid bending contacts.

Use a very small instrumentation screwdriver to release locking spade on yellow and white wires. To unlock slide screwdriver in slot along wire entry to controller body while gently pulling on wire. Note position of wires and replace on new unit in same position/order. Plug new run capacitor into new controller being careful to orient capacitor to proper position (hole matches guide on controller unit). Plug newly installed controller and capacitor into condensor and replace bail wire.

Make sure timer is not in defrost mode - manually advance timer if necessary to ensure timer is in run mode. Turn temperature control to coldest setting. Plug in and hopefully enjoy the humming noise of your newly repaired and operational compressor and freezer.

Removed old cold temperature control; tested with ohm meter and determined that the control was bad; ordered new cold control from PartSelect.com. Installed new cold temperature control with no problems; freezer is now running like new again!
p.s. I was very pleased with how fast I received my order from PartSelect.com!

Very simple repair. Removed the bail that holds the compressor controller and run capacitor from the compressor, removed the controller & capacitor, inserted a very small screwdriver into the controller to compress the barbs that hold the electrical wires to the controller. Plugged in the wires to the new controller in the same position a ... Read more s the original, plugged in the capacitor and then plugged the entire unit back onto the compressor, replaced the wire bail, plugged in the freezer and repair was complete.

First I removed the clamp, pulled out the part, and diconnected the two wires on the side and a small screw. Reconnected the new part with the small screw, connected the wires and plugged the part back to the side of the motor. Whaa La, Done.

Removed old gasket, then installed new gasket. Make sure to allow new gasket to set out for a few days prior to installing to get all wrinkles out, use a heat gun after installing to make gasket shape to freezer door.

removed door and took all the screws out of the inside door rack. removed old door seal . replaced door seal and made sure that the seal fit around and door rack fit into the groove then replaced all screws and tightened choosing random sections to tighten .replaced the door plugged back in wires that I removed and replaced door hinge scr ... Read more ews . Shut door and checked sealing 2 hours later .Complete seal .

Needed a Phillips head screwdriver to remove bottom plate (kick panel). UNPLUGGED FREEZER. Removed plate pulled switch out through the mounting hole and unhooked the two electric wires. Plac ... Read more ed wires on new switch, pushed wires back through the hole and seated the switch. Plugged in the freezer and opened the door - magic, the light came on. Replaced the front kick panel (hardest part was to line up the plate holes with the holes in the mounting bracket).

Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.

I removed the plate (recommend using a magnetic phillips head screw driver to remmove screws which are recessed). I removed the old part and pushed the new part through the hole and carefully reached in behindto attach the wires to the new part.

Unplugged the freezer. Located the Run Capacitor (next to the compressor). Removed the wire holding bracket, removed the Run Capacitor from the Start Relay. Installed the NEW Capacitor, re-installed the holding bracket. Plugged the unit in, looking at the display for the proper start-up sequence data. All is good - freezer operating for a ... Read more nother 10+ yrs. NOTE: When removing the Run Capacitor, beware the COMPRESSOR could be HOT to the touch.

On 08/13 / 2025 starting in the AM --- My Wife Marie Defrosted -- Cleaned and dried the Kenmore up right freezer she has had for more than 33 years --- She noticed there was screws behind the inside door gasket and informed yours truly --- 1st Jacques loosened all the screws then removed the old gasket -- took it cleaned it and boxed it ... Read more in the box the new gasket came in --- Took new freezer door gasket and installed it neatly around the door by tucking back part of door gasket between door panel and door --- once all was in place started tightening all screws starting at bottom holding bottom gasket material tight with other hand --- then working counter clock wise till done !!! there you go it was very easy and turned out great !!! Now everything is like new !!! Jacques And Marie / from Virginia

Loosen screws, removed old gasket seal, replace with new gasket (nice to use 2 sets of hands) and re screwed. Used hairdryer to heat up and fluff out a spot that wasnt seal all the way. Pretty simplementation to do.

I paid attention to how the old part came off. You need a small (very small) flat bladed screwdriver to release the two wires that plug into the controller. I checked that it was a bit difficult but it would had been easier if I could have found a screwdriver sooner.