Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice tray wouldent fill.
It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!
Support stude for both vegetable crispers broken off
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.
None of this was obvious - an online tip from another member was invaluable.
The top crisper drawer frame was cracked, it secures the glass top also.
Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.
Popped out glass, pulled up and the front of cover and pulled froward. Pushed new cover back on to studs and pushed down on cover to lock it to front studs. Put glass on top of new cover. About 3 min total to make repair.
After a power outage my refrigerator went warm & the freezer was cool.
I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.
Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.
Icemaker worked sporadically, infrequently, not at all
Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.
Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!
2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°
Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running
Shut off water supply at the main, drained water from lines, pushed filter in from end of filter then pulled out. Removed the 2 plastic protecting tubes from the inlet and outlet stems. Made sure filter was facing same way as the old one, pushed filter in making sure it was locked, turned water supply on slowly, ran about a gallon of water thru filter. If not done the taste is odd. 5 minute repair.