FFHT1826LS3 Frigidaire Refrigerator - Instructions

replaced broken one

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.

Disconnect the power. To install the Defrost timer which is located inside the console at the top of the fridge I followed a YouTube video. It is very easy. Keep in mind that the Defrost timer comes settled in defrost mode so the compressor will not start after the power is reconnected.There is a hole in the console just behind the Defrost timer where you engaged it with a flat driver and rotate the clock until the compresor start. Now the compressor works for 6 hours and stop for 20 minutes for the defrosting cicle. The freezer now is freezing the meat!!

Just like the video , just pull out the crisper drawers and slide the new one in. I also made sue that I had a quilt on the floor in case I dropped the glass shelf. Also if you are not sure of the model number you can try calling the store where you bought the appliance at which I had to do. I bought it at Conns and they just needed the phone number I used when I bought it.

Literally all I needed to do for the door shelf was press it into place, and for the crisper drawer cover so just needed to remove the crisper drawers, lift away the glass shelf (after removing contents from the fridge, obviously) and then remove the drawer frame and replace the broken one (which again, had been broken from before I moved in here almost six years ago!), and then reassemble. It's very nice to have space for seltzer or beer cans in the door and not to have the sagging shelf like I had before. Worth the money and very easy to source.

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.

Unboxed parts and snapped into place, no tools required . Good price, quick shipment---very pleased !

I simply removed the old broken shelf and clipped in the new one. Not a major project however the company went above and beyond due to a problem with the delivery of the part. I live in an 1,800 unit condo. Packages are delivered to a kiosk for pick up. FedEx showed the package was delivered but I did not receive it. When I called PartSelect to advise of the problem, they immediately refunded me for the part I didn't receive and sent another one which I received in a few days. I found the company to be very reliable and customer friendly. I will use them again should the occasion arise.

Installed in a snap !!!!

Replaced it with one like the lower freezer door bin. Very easy, just snapped into place.

The part fit perfectly. I simply placed the ends on the holes on the side wall inside the refrigerator, and the other end of the shelf slipped right into the matching holes on the other side. That easy!

Just slide glass in. Very easy.

Snapped the door shelf into place