FFHS2622MS3 Frigidaire Refrigerator - Parts

This door bin (Bottom Door Bin, Refrigerator Door Bin, Door Shelf Bin, Refrigerator Door Bin) is a movable bin mounted on the inner door to hold food items, bottles, and jars. Over time, a cold refrigerator can cause plastic to become fragile and break down. This can lead to other issues in the refrigerator. When the door bin will not hol...Read mored securely onto the inner door panel, it must be replaced. This door bin measures 5.75 inches high, 16 inches wide, by 4.25 inches deep and is made of white plastic. Sold individually.

This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is a...Read moren easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.

This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your us...Read moreer manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.

This OEM white door bin is made of white plastic and is easy to install. It is used to hold items in the fridge, and you'll be able to visually see if the part is broken. This part attaches to the fridge door. You can check if this model is right for your appliance by checking your user manual and model number. The size of this door bin i...Read mores approximately 15.42 inches wide x 7.1 inches deep x 5.04 inches in height and holds 1 gallon. No tools will be required to complete this repair, which our customers rated as very easy, and only takes a minute. Just pop the old part out of place and snap the new one in. This part is sold individually.

This original equipment manufacturer Door Shelf is a white plastic part which holds items inside of your freezer or refrigerator door. It is roughly 10 inches long by 4 inches high by 5.5 inches wide. It can be used in the freezer or refrigerator and is very easy to repair. All you need to do is snap the new door bin into place, which req...Read moreuires no tools. This part is sold individually and not as part of a set, even though your refrigerator may take more than one of this part.

The function of the Refrigerator Water Inlet Valve (Triple Solenoid Water-Valve, Water Valve, Water Inlet Valve, Refrigerator Water Inlet Valve Assembly) is to release water from the supply line when activated, and send it through to your water dispenser or ice maker in your refrigerator. The water inlet valve is located at the back of th...Read moree refrigerator, and connects to the water supply. The valve can break from material fatigue or normal use. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. This valve measures approximately 7 inches long and 4.5 inches wide, and is constructed of plastic and metal. It comes in blue, and includes the valve and mounting bracket.

This clear plastic crisper drawer is for side-by-side refrigerators. It is sold individually and sourced right from the original manufacturer. Please note that the new pan does not have the humidity control slide, and this component is now sold separately. The crisper drawer is designed to store produce at a humidity level that ensures yo...Read moreur food is kept fresh for as long as possible. It is commonly replaced because it is cracked, warped, or stained. For this simple tool-free repair, start by opening your refrigerator door and sliding out the old crisper drawer. Take your new crisper drawer and align the thin ridge on the top of the drawer with the track located inside the refrigerator. Slide the new part into place and your repair is complete.

This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the l...Read moreimit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Cracked crisper glass? This replacement insert is just what you need. It’s about 17.12" by 15.40" and fits right into the frame above your crisper drawers, giving you extra shelf space and keeping things neat. Made of sturdy glass and easy to install—just slide the old one out and pop the new one in. Sold individually, so make sure it matches your fridge model before ordering!

This refrigerator shelf frame is designed to sit directly above the bottom crisper drawer, helping to regulate humidity and maintain optimal conditions for storing fresh produce. Built for durability and a precise fit, it supports the glass shelf (sold separately) and contributes to the overall organization of your refrigerator’s interior...Read more. Please note that this part includes the frame only; the glass insert must be ordered separately.

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.

This ice container assembly is designed to securely store ice within your refrigerator while facilitating efficient dispensing. The kit includes the ice container, auger, and blades, all engineered for seamless integration with compatible models. The auger mechanism rotates to move ice toward the dispenser, while the blades help break up ...Read moreclumps for consistent flow. Replacing the assembly is a straightforward process that requires no tools. Begin by turning off the ice maker, then remove the existing container from the freezer compartment. Align the connector with the auger yoke and slide the new container into position. Once installed, the ice maker can be turned back on, restoring full functionality.