FFHB2740PP Refrigerator - Instructions

The diagram on the frigidaire website said 4 screws and 3 wires to disconnect and part comes out and reverse the steps for install actually took less then 5 mins...easiest and first repair I have done and the part was 20 bucks cheaper at parts select then anywhere else on the internet!

Removed the trough that catches the ice.. two philips screws to take the front cover off. Side and bottom. Than quarter inch to remove cover over wires. Unplug ones to ice maker. Slide out a little and down. May be a zip tie in the back cut with sheet rock knife. Reverse to install.

I pulled the old one out and pushed the new one in place.

Snapped the new shelf in.

We just slide in the bin.

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water fi ... Read more lter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off ... Read more and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Remove frozen food and ice cubes to coolers so they stay frozen.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on ... Read more the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a rolle ... Read more r type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
[email protected]
8042627963

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon be ... Read more gan to make aloud noise, due to there not being enough clerance.

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse