Parts That Fix Frigidaire Washer Dryer Combo FEX831FS2 Leaking
Leaking is a commonly reported symptom for the FEX831FS2 Frigidaire Washer Dryer Combo, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FEX831FS2 Frigidaire Washer Dryer Combo that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace your old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.
This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before placing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
The tub ring seal or splash cover seal is used for washers. This part seals the tub cover to the outer one and prevents water leakage from around the tub ring. If your seal is damaged and you are experiencing water leakage, it is best to replace this part. Refer to the manual provided by the manufacturer for further installation instructions. Remember to unplug your washer from the power source before starting this installation process.
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.
The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, therefore ensuring the shaft is spun properly during its spin cycle. If your spin cycle makes loud or odd noises, replacing the bearing could be a solution to your problem. Refer to the diagram provided by the manufacturer for further installation instructions. As a safety precaution make sure to unplug appliance from the power source.
This water inlet hose is used in washers. The hose connects the washer water inlet valve to the water supply in your home. There are two solenoids on the valve, which are referred to as coils, and there are two wires attached to each solenoid that should be labelled to ensure they are properly reconnected after replacing the new hose. Over time, your hose can begin to leak which can lead to floods. Replacing your hose earlier on can prevent this problem. Refer to the diagram provided by the manufacturer for installation instructions. Remember to unplug your appliance from the power source before beginning this installation project.
This part helps with the spinning and agitating cycles.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.