FEX831FS0 Frigidaire Washer Dryer Combo - Parts

This blower wheel is a genuine OEM replacement part for your dryer. The wheel can become damaged through use of the dryer, especially if the drive motor shaft, which it is attached to, becomes damaged. This repair will require some disassembly of the dryer. Make sure to disconnect the power source and wear appropriate work gloves while conducting this repair.

This kit includes 3 screws and 3 terminals.

This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before plac...Read moreing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.

Sold individually.

This is an agitator that is compatible within various makes and models of washer, and is used to move, or agitate, the clothes and soap/water mixture around within the tub of the washer. This agitator is made of a high-quality white plastic and is installed down the center of the main washer tub. This agitator requires a cap and seal on i...Read morets top to fasten and secure it within the washer, but is sold as an individual agitator. If you notice your clothes are not being cleaned or are covered in soap residue, it is likely that the agitator base is stripped or broken, leading to the agitator being unable to rotate and move properly. It is recommended that when you remove the agitator, you inspect the directional cogs, also known as dogs, or whatever hardware is attached to the base of the agitator, like the trunnion, for any damage or wear, since those parts are commonly replaced when agitators stop working properly. Replacing this agitator is as simple as removing its cap and seal, which will allow you to remove the agitator and replace it.

The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your washer is making loud noises while washing, this may indicate an issue with the agitator block. You will find this part underneath the dispenser cover and cup. Y...Read moreou will need a 1/2-inch socket to remove the agitator bolt and then simply lift off the agitator (this may require some effort to lift off). Use a flat-head screwdriver to remove the old drive block, push the new one into place with firmness. This part is made of metal and measures about 2 inches long and 1 inch wide.

The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, therefore ensuring the shaft is spun properly during its spin cycle. If your spin cycle makes loud or odd noises, replacing the bearing could be a solution to your pr...Read moreoblem. Refer to the diagram provided by the manufacturer for further installation instructions. As a safety precaution make sure to unplug appliance from the power source.

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front ...Read morepanel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

This operating or cycling thermostat is used in dryers to monitor and direct the temperature inside the dryer. If your thermostat is shorted out and it will not allow the heat to come on, it is best to replace it. The tool needed for this repair is a 1/4 inch nut driver. The first step for this repair is to access the back panel and remov...Read moree the screws. Next, remove wires connected to the thermostat and remove the screw to pull out the thermostat. Now you can install new thermostat. For further installation instructions, refer to the diagram provided by the manufacturer. As a safety precaution, remember to unplug your appliance from the power source before starting this repair.

Sold individually.

This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the tension spring is if you notice that your washer is not spinning or agitating, the drive belt has come loose, and the idler pulley is no longer secure. To access t...Read morehis part, you will need to remove the front of your washer. The spring is located underneath the bottom of the tub. This is a genuine OEM part that comes right from the manufacturer.

This part is used to activate the lid switch when the lid opens/closes.