EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FES367CEBA Frigidaire Range - Instructions

All Instructions for the FES367CEBA
46 - 60 of 81

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lens cover for oven light broke.
0 of 1 people found this instruction helpful.
  • Amy from Corona, CA
  • Really Easy
  • Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!
had no instructions on how to remove old door hinge recepticle..
0 of 1 people found this instruction helpful.
  • Douglas from Colrain, MA
  • Difficult
  • 1- 2 hours
  • Screw drivers
After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.
Was this helpful?
Thank you for voting!
Control will not work - only clock blinks
0 of 4 people found this instruction helpful.
  • Sue from Lampasas, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this helpful?
Thank you for voting!
Broken globe in oven and burnt out light bulb
0 of 5 people found this instruction helpful.
  • Sharon from Foley, AL
  • Really Easy
  • Less than 15 mins
Easy as 1-2-3
Other Parts Used:
Was this helpful?
Thank you for voting!
Switch shorted out.
  • Todd from Cynthiana, KY
  • Easy
  • Less than 15 mins
  • Nutdriver
Unplug the stove and remove back panel. Remove the two wires connected to the bad switch. Push the bad switch through the front panel on the stove. Installed new switch and connect the two wires back to the new switch. Install back panel on the stove and plug stove back in. Switch is working fine.
Was this helpful?
Thank you for voting!
Stove door switch was broken
  • James from Milford, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..
Was this helpful?
Thank you for voting!
Bake element went out on my oven
  • Jeffery from Union Point, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.
Was this helpful?
Thank you for voting!
Coil melted in half.
  • Gerald from Artesia, NM
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!
Was this helpful?
Thank you for voting!
Door gasket was worn, stained and needed replaced
  • BETSY from HENDERSONVILLE, NC
  • Really Easy
  • Less than 15 mins
Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is d escribed properly. I would buy from this company again!
Was this helpful?
Thank you for voting!
broiler element burned out
  • Richard from Oro Valley, AZ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
watched a U-Tube video on this subject.....worked like aa charm!!
Was this helpful?
Thank you for voting!
Bottom element in oven not heating.
  • Catherine from San Saba, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.
Was this helpful?
Thank you for voting!
Heating element burned out
  • Jack from Hedgesville, WV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took screws loose, unplugged old one plugged in new one put screws back
Was this helpful?
Thank you for voting!
lower oven element burned up
  • Constantine from Vero Beach, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.
Was this helpful?
Thank you for voting!
end caps that hold the stove at proper depth and support control panels broken
  • WILLIAM from RIDGE, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
repair was pretty simple. i pulled stove out from cabinet and unplugged it. Then i removed the screws that hold the face panel in place and gently slid out panel as far as i could without damaging wires. i had to remove the small switches that control the two two size burners as well as one thermostat on the right side so i can access the nuts holding the plastic end caps in place. i diagramed the color coded wires so i didnt mix them up.took off the old end caps replaced with new caps and put back together.. took about a half hour as this was my first time inside the guts of this stove.. stove is baack in place and as good as new again.
Was this helpful?
Thank you for voting!
Oven did not work since bake element did not warm up.
  • Russell from North Smithfield, RI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.
Was this helpful?
Thank you for voting!
All Instructions for the FES367CEBA
46 - 60 of 81