Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.
4 of 4 peoplefound this instruction helpful.
Charles from OMAHA, NE
Really Easy
15 - 30 mins
Screw drivers
Pulled stove out and unplugged it. Used a Phillips screwdriver to take the back cover off of the control panel. Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p
... Read moreanel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others. Replace back cover. Plug stove back in and slide back into place. There are you tube videos out there to help you.
Read less
Was this helpful?
Thank you for voting!
Couldn't find replacement trays locally. Part Select was very helpful and prompt in shipping.
5 of 7 peoplefound this instruction helpful.
Rosemary from St. Albans, ME
Really Easy
Less than 15 mins
Just placed the chrome bowl trays in place and was good to go. They look very nice.
Was this helpful?
Thank you for voting!
Bake element burned out
5 of 7 peoplefound this instruction helpful.
Sylvia from Escondido, CA
Really Easy
Less than 15 mins
Screw drivers
Took out the bad element and replaced it with the new element in less than 5 minutes, worked perfect, thanks
Was this helpful?
Thank you for voting!
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
5 of 7 peoplefound this instruction helpful.
Phyllis from GAINESVILLE, GA
Easy
Less than 15 mins
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in
... Read morethe house.....I show them what I DID!! :-)
Read less
Was this helpful?
Thank you for voting!
Coroded drip pans
4 of 5 peoplefound this instruction helpful.
Lori from Old Town, FL
Really Easy
Less than 15 mins
Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Drip bowels needed to be replaced
3 of 3 peoplefound this instruction helpful.
Francine from OTEGO, NY
Very Easy
Less than 15 mins
I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this helpful?
Thank you for voting!
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 peoplefound this instruction helpful.
Daniel from Falmouth, MA
A Bit Difficult
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely. Once all was replaced and reinstalled the oven
... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Read less
Was this helpful?
Thank you for voting!
Lens cover for the oven light
3 of 4 peoplefound this instruction helpful.
Larry from COZAD, NE
Really Easy
30 - 60 mins
Very easy just had to pull the wire up that holds it secure.
Was this helpful?
Thank you for voting!
Element had burned out
4 of 7 peoplefound this instruction helpful.
John from Pearland, TX
Really Easy
Less than 15 mins
Screw drivers
Extremely easy. Two screws and electric connection that had easy pop on-off connection.
Was this helpful?
Thank you for voting!
Worn Drip Bowls
2 of 2 peoplefound this instruction helpful.
River Oaks Town Homes from DES MOINES, IA
Very Easy
Less than 15 mins
Pulled out the old drip bowls and replaced with the new. A simple snap!
My Orders
![Chrome Drip Bowl - 6" – Part Number: 316048414](https://partstown.sirv.com/products/FRI/FRI316048414/FRI316048414_01.jpg?w=100&h=75&scale.option=fit&canvas.width=100&canvas.height=75&canvas.color=white "Chrome Drip Bowl - 6" – Part Number: 316048414")
![Drip Bowl - 8" – Part Number: 316048413](https://partstown.sirv.com/products/FRI/FRI316048413/FRI316048413_01.jpg?w=100&h=75&scale.option=fit&canvas.width=100&canvas.height=75&canvas.color=white "Drip Bowl - 8" – Part Number: 316048413")