FEFS66DSH Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
L.F. large burner element either on full hot or off. Would not cycle in and out with element control switch setting.
4 of 4 people
found this instruction helpful.
-
Gerald from MADISON HTS, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it starte
... Read more
d but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.
Read less
Was this helpful?
Thank you for voting!
Had aluminum foil stuck on bottom
4 of 4 people
found this instruction helpful.
-
George from JACKSON, MI
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed 2 screws, pulled out the panel, replaced the new panel and replaced the two screws. Less than 5 minutes.
Was this helpful?
Thank you for voting!
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
5 of 7 people
found this instruction helpful.
-
Phyllis from GAINESVILLE, GA
- Easy
- Less than 15 mins
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in
... Read more
the house.....I show them what I DID!! :-)
Read less
Was this helpful?
Thank you for voting!
Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.
4 of 4 people
found this instruction helpful.
-
Charles from OMAHA, NE
- Really Easy
- 15 - 30 mins
-
Screw drivers
Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p ... Read more anel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p ... Read more anel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.
Read less
Was this helpful?
Thank you for voting!
The oven bake element developed a hot spot which failed shortly after the hot spot developed.
4 of 4 people
found this instruction helpful.
-
Dave from BRISTOL, VA
- Very Easy
- Less than 15 mins
-
Nutdriver
Unplug the stove or disconnect at the breaker. Open the oven and remove the bake racks. Using a nut driver (or Phillips Screwdriver) remove the screws (one per side) that secure the bake element. Place them in a safe/secure place outside of the oven. Carefully pull straight back on the element until about 3 inches of the wire, that connec
... Read more
ts to the element, is exposed. Carefully unplug the wire from each element (make sure that the wire does not pull back into the oven insulation. I placed a small metal clip on each wire). Remove the old element and plug the new one in. Put everything back in the exact same way you took the old one out. Power the oven up and preheat your oven. Monitor this - should be no problem at all. Very simple process. My first attempt at this and it was very easy.
Read less
Was this helpful?
Thank you for voting!
element burnt out
5 of 7 people
found this instruction helpful.
-
Demoris from GOLDSBORO, NC
- Really Easy
- 15 - 30 mins
purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.
Was this helpful?
Thank you for voting!
Right - front dual element not working.
4 of 5 people
found this instruction helpful.
-
Douglas from VIRGINIA BCH, VA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clip
... Read more
s one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).
Read less
Was this helpful?
Thank you for voting!
Bottom burner wouldn’t heat
5 of 8 people
found this instruction helpful.
-
cynthia from SEBRING, FL
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Watched the video
Was this helpful?
Thank you for voting!
oven baking element burnt into
4 of 5 people
found this instruction helpful.
-
Teresa from Marengo, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great
Was this helpful?
Thank you for voting!
Bake elemen t shorted out.
3 of 3 people
found this instruction helpful.
-
LARRY from LEES SUMMIT, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers
Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.
Was this helpful?
Thank you for voting!
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
3 of 3 people
found this instruction helpful.
-
Leota from AUXVASSE, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and M
... Read more
ama is happy!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The oven stopped working
3 of 3 people
found this instruction helpful.
-
mary from West Winfield, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
We watched the video instruction which was very helpful. We unplugged the stove and removed the back panels. Then we carefully disconnected the oven electronic control board and removed it. We used the putty knife to peel off the face plate from the old control board and secured it to the new one. We put the new control board in place and
... Read more
reconnected the wiring. We put the back panels on and plugged the stove in. It was very easy to complete the whole process. Unfortunately, the oven did not work but the broiler element did. We had to place another order for the oven bake element purchase. Otherwise all went well and there were no casualties.
Read less
Was this helpful?
Thank you for voting!
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 people
found this instruction helpful.
-
Daniel from Falmouth, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Read less
Was this helpful?
Thank you for voting!
Burnt out baking element
3 of 3 people
found this instruction helpful.
-
Joseph from HAMPTON, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the back panel, disconnected the terminals and removed the old one and installed the new one.
Was this helpful?
Thank you for voting!
Right rear burner not working properly
3 of 3 people
found this instruction helpful.
-
Dante from SOUTHOLD, NY
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as
... Read more
the video showed his switch matched each wire? My installation was sideways??
Read less
Was this helpful?
Thank you for voting!