FEFL74ASG Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lens was broken
2 of 3 people
found this instruction helpful.
-
Kenneth from Coeur d'Alene, ID
- Really Easy
- Less than 15 mins
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this helpful?
Thank you for voting!
Broken right side parts for lower over storage drawer.
2 of 3 people
found this instruction helpful.
-
Ty from Baltimore, MD
- Easy
- Less than 15 mins
-
Screw drivers
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Other Parts Used:
Was this helpful?
Thank you for voting!
The right Drawer Glide was broken.
2 of 3 people
found this instruction helpful.
-
Fred from Gregory, MI
- Really Easy
- Less than 15 mins
The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.
Was this helpful?
Thank you for voting!
Lacking oven racks on used appliance
2 of 3 people
found this instruction helpful.
-
Katherine from Roanoke, VA
- Really Easy
- Less than 15 mins
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this helpful?
Thank you for voting!
Large front burner would not come on under setting of "3"
3 of 7 people
found this instruction helpful.
-
Steven from Edina, MN
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Replaced infinite control very easily.
Was this helpful?
Thank you for voting!
over draw was off track
1 person
found this instruction helpful.
-
Frances from Hauppauge, NY
- Really Easy
- Less than 15 mins
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Was this helpful?
Thank you for voting!
oven drawer would not open or shut completely
1 person
found this instruction helpful.
-
Howard from Poteau, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time
Was this helpful?
Thank you for voting!
originaldrawer guide was cruched out of useable shape
1 person
found this instruction helpful.
-
Fred from Ocala, FL
- Really Easy
- Less than 15 mins
-
Pliers
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Fred . it was so reasonable i got a spare.
Was this helpful?
Thank you for voting!
Needed an additional rack
1 person
found this instruction helpful.
-
Gary from Darragh, PA
- Really Easy
- Less than 15 mins
Open the door and slide in the new rack.
Was this helpful?
Thank you for voting!
cracked range oven door handle
1 person
found this instruction helpful.
-
michael from morton, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
removed 2 screws from inside oven door swap out old to new handle reinstall 2 screws done less than 15 min.
Was this helpful?
Thank you for voting!
Burners constantly overheating, and inconsistent heating.
1 person
found this instruction helpful.
-
David from MOUNT VERNON, ME
- Very Easy
- Less than 15 mins
-
Pliers
With the stove pulled out and unplugged, There are 4 square head screws to pull a metal plate off the back of the range. Once that is off, the infinite switches are in line and can be removed with a philips head screw driver/bit. I placed each wire onto the new switch as I removed them from the old, to avoid any confusion. The entire repa
... Read more
ir took less than 10 minutes. Incredibly easy.
Read less
Was this helpful?
Thank you for voting!
One guide was missing and the other was broken
1 person
found this instruction helpful.
-
Don from WEST UNION, OH
- Really Easy
- Less than 15 mins
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Was this helpful?
Thank you for voting!
8" burners were not responding correctly to the switches
1 person
found this instruction helpful.
-
Carl from W SAND LAKE, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elem
... Read more
ents. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.
Read less
Was this helpful?
Thank you for voting!
Switch quit working and wouldn't turn
1 person
found this instruction helpful.
-
Jim from UNIONTOWN, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!
Was this helpful?
Thank you for voting!
The element gets very even the control is at minimum
1 person
found this instruction helpful.
-
adolfo from new york, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this helpful?
Thank you for voting!