EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FEFB89ECH Frigidaire Range - Instructions

All Instructions for the FEFB89ECH
61 - 75 of 128

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stove was dropped and had broken, bent frame and adjuster feet
2 of 2 people found this instruction helpful.
  • Paul from PORT ORANGE, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this helpful?
Thank you for voting!
run away temp
3 of 5 people found this instruction helpful.
  • James from ELKHORN, WI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.
Was this helpful?
Thank you for voting!
oven was over heating temp. of oven keep climbing
2 of 2 people found this instruction helpful.
  • Herbert from MARIETTA, OH
  • Very Easy
  • Less than 15 mins
  • Nutdriver
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this helpful?
Thank you for voting!
Oven temperature was not consistent.
2 of 3 people found this instruction helpful.
  • Kimberly from OWASSO, OK
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Was this helpful?
Thank you for voting!
There was no instructions. The wires don't match up old vs new. I read the reviews and this helped.
2 of 3 people found this instruction helpful.
  • Lisa from APACHE JCT, AZ
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
However the 1a 1b etc. Are very hard to see thus the need to magnify. Then it was easy.
I must say the guy I talked to was very nice.
Was this helpful?
Thank you for voting!
Element burned out
1 person found this instruction helpful.
  • Stephen from AUGUSTA, ME
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Turned off power at breaker, took back off range, removed red and blue wires, removed oven door, removed two screws holding in broil element, removed wires supporting old element, installed new element and reversed procedure.
Was this helpful?
Thank you for voting!
Old terminal block was melted
1 person found this instruction helpful.
  • Anthony from LEWES, DE
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
removed back panel on range, removed old terminal block installed new terminal block, replaced back panel cover.
Was this helpful?
Thank you for voting!
Replace oven element
1 person found this instruction helpful.
  • Connie from BARTLESVILLE, OK
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Watched the included video and duplicated.
Was this helpful?
Thank you for voting!
Element would not heat up
1 person found this instruction helpful.
  • Everett from Colchester, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be su re to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Was this helpful?
Thank you for voting!
wrong part
2 of 4 people found this instruction helpful.
  • Barbara from WICKENBURG, AZ
  • Very Difficult
  • 30 - 60 mins
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this helpful?
Thank you for voting!
some of the buttons quit working
1 person found this instruction helpful.
  • Marshall from Grafton, WI
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers
I followed instructions found on the interwebs. They helped immensely. Saving the original faceplate was tricky. The replacement control board works perfectly.
Was this helpful?
Thank you for voting!
temp. probe
1 of 2 people found this instruction helpful.
  • Deane from WINCHESTER, KY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy watched on line video
Was this helpful?
Thank you for voting!
Oven would not reach temperature or it would finally reach temp but would not stay warm.
1 of 2 people found this instruction helpful.
  • Craig from FAYETTEVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclock wise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people found this instruction helpful.
  • Denise from Landover, MD
  • Really Easy
  • Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
I had a F31 code which means oven isn't working
1 of 3 people found this instruction helpful.
  • Terry from CHELSEA, OK
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Called fridgidaire and they told me the a F31 code means my temperature sensor is not working.
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
Was this helpful?
Thank you for voting!
All Instructions for the FEFB89ECH
61 - 75 of 128