EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FEF389CESA Frigidaire Range - Instructions

All Instructions for the FEF389CESA
61 - 75 of 707

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven bake element developed a hot spot which failed shortly after the hot spot developed.
4 of 4 people found this instruction helpful.
  • Dave from BRISTOL, VA
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Unplug the stove or disconnect at the breaker. Open the oven and remove the bake racks. Using a nut driver (or Phillips Screwdriver) remove the screws (one per side) that secure the bake element. Place them in a safe/secure place outside of the oven. Carefully pull straight back on the element until about 3 inches of the wire, that connec ts to the element, is exposed. Carefully unplug the wire from each element (make sure that the wire does not pull back into the oven insulation. I placed a small metal clip on each wire). Remove the old element and plug the new one in. Put everything back in the exact same way you took the old one out. Power the oven up and preheat your oven. Monitor this - should be no problem at all. Very simple process. My first attempt at this and it was very easy.
Was this helpful?
Thank you for voting!
Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.
4 of 4 people found this instruction helpful.
  • Charles from OMAHA, NE
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p anel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.
Was this helpful?
Thank you for voting!
The glass on the enter oven door was broken
4 of 4 people found this instruction helpful.
  • leslie from Pickerington, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...
Was this helpful?
Thank you for voting!
Bottom burner wouldn’t heat
5 of 8 people found this instruction helpful.
  • cynthia from SEBRING, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Watched the video
Was this helpful?
Thank you for voting!
Old racks had melted plastic on them.
4 of 5 people found this instruction helpful.
  • James from PAINESVILLE, OH
  • Very Easy
  • Less than 15 mins
It was a replace racks not repair. No problem
Was this helpful?
Thank you for voting!
The neon tube over the stove top went out
8 of 17 people found this instruction helpful.
  • Gunther from Columbia, SC
  • Really Easy
  • Less than 15 mins
Put a new one in.
Was this helpful?
Thank you for voting!
oven baking element burnt into
4 of 5 people found this instruction helpful.
  • Teresa from Marengo, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Socket set
my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great
Was this helpful?
Thank you for voting!
replacing oven racks
4 of 5 people found this instruction helpful.
  • Lawrence from Elmira, NY
  • Really Easy
  • Less than 15 mins
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this helpful?
Thank you for voting!
the old bake element was corroded and non-funtional
5 of 9 people found this instruction helpful.
  • Stephen from RONAN, MT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people found this instruction helpful.
  • Alan from SAN MATEO, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Bake element went out
4 of 6 people found this instruction helpful.
  • Nicholas from COTTONDALE, AL
  • Really Easy
  • Less than 15 mins
  • Socket set
The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. P ull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.
Was this helpful?
Thank you for voting!
Oven would not heat
3 of 3 people found this instruction helpful.
  • Kevin from Swanville, ME
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.
Was this helpful?
Thank you for voting!
Bake element began burning itself up.
3 of 3 people found this instruction helpful.
  • Don L from La Grande, OR
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.
Was this helpful?
Thank you for voting!
Burnt out baking element
3 of 3 people found this instruction helpful.
  • Joseph from HAMPTON, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed the back panel, disconnected the terminals and removed the old one and installed the new one.
Was this helpful?
Thank you for voting!
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 people found this instruction helpful.
  • Daniel from Falmouth, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this helpful?
Thank you for voting!
All Instructions for the FEF389CESA
61 - 75 of 707