FEF369HCD Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Light bulb went out
7 of 12 people
found this instruction helpful.
-
ANGELA from MEBANE, NC
- Very Easy
- Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
Oven temperature ran very high
5 of 6 people
found this instruction helpful.
-
Juliette from BRINKLEY, AR
- Easy
- 30 - 60 mins
-
Screw drivers
When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced th
... Read more
e back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Had aluminum foil stuck on bottom
4 of 4 people
found this instruction helpful.
-
George from JACKSON, MI
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed 2 screws, pulled out the panel, replaced the new panel and replaced the two screws. Less than 5 minutes.
Was this helpful?
Thank you for voting!
Large Burner of left-front element not heating
5 of 7 people
found this instruction helpful.
-
Matthias from Poway, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced the entire element which has both a large and a small heated element.
1. Removed 2 screws holding the cooktop. Located on front of cooktop after opening oven door.
2. Raised cooktop
3. Unscrewed the long bracket holding the 2 front burners 4. unscrewed the burner element from bracket.
5. Wrote down the ... Read more wiring, removed the wiring with pliers.
6. Removed the spring clips holding the burner element to the bracket with pliers.
7. Unscrewed/removed spring clips from old element
8. Install reverse of removal.
The only thing I should have done was to mark which holes the spring clips were originally were in on the long bracket. It ended up OK, but it would have been faster if I didn't have to double-check the positioning of the burner.
1. Removed 2 screws holding the cooktop. Located on front of cooktop after opening oven door.
2. Raised cooktop
3. Unscrewed the long bracket holding the 2 front burners 4. unscrewed the burner element from bracket.
5. Wrote down the ... Read more wiring, removed the wiring with pliers.
6. Removed the spring clips holding the burner element to the bracket with pliers.
7. Unscrewed/removed spring clips from old element
8. Install reverse of removal.
The only thing I should have done was to mark which holes the spring clips were originally were in on the long bracket. It ended up OK, but it would have been faster if I didn't have to double-check the positioning of the burner.
Read less
Was this helpful?
Thank you for voting!
oven temp was not heating up to desired temp and using an oven thermometer to confirm
4 of 4 people
found this instruction helpful.
-
philip from CLIFTON, NJ
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved
Was this helpful?
Thank you for voting!
slow to get to temperature
4 of 4 people
found this instruction helpful.
-
SHAUN from ALBUQUERQUE, NM
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.
Was this helpful?
Thank you for voting!
Oven was not heating up properly
4 of 5 people
found this instruction helpful.
-
Robert from GILROY, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.
Oven is working great now.
Our iss ... Read more ues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.
If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.
Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.
Thanks
Oven is working great now.
Our iss ... Read more ues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.
If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.
Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.
Thanks
Read less
Was this helpful?
Thank you for voting!
F10 code going off
4 of 5 people
found this instruction helpful.
-
edward from BRISTOL, IN
- Really Easy
- 30 - 60 mins
-
Screw drivers
Went well, and working thank you ??
Was this helpful?
Thank you for voting!
Right rear burner not working properly
3 of 3 people
found this instruction helpful.
-
Dante from SOUTHOLD, NY
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as
... Read more
the video showed his switch matched each wire? My installation was sideways??
Read less
Was this helpful?
Thank you for voting!
The oven stopped working
3 of 3 people
found this instruction helpful.
-
mary from West Winfield, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
We watched the video instruction which was very helpful. We unplugged the stove and removed the back panels. Then we carefully disconnected the oven electronic control board and removed it. We used the putty knife to peel off the face plate from the old control board and secured it to the new one. We put the new control board in place and
... Read more
reconnected the wiring. We put the back panels on and plugged the stove in. It was very easy to complete the whole process. Unfortunately, the oven did not work but the broiler element did. We had to place another order for the oven bake element purchase. Otherwise all went well and there were no casualties.
Read less
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people
found this instruction helpful.
-
Alan from SAN MATEO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Oven wasn’t heating
3 of 3 people
found this instruction helpful.
-
Felicia from FORT MILL, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Used instruction video & replaced part.
Was this helpful?
Thank you for voting!
Oven did not heat after replacing element
3 of 4 people
found this instruction helpful.
-
Ron from ORLANDO, FL
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First unplug range. Remove 6 screws on back of range( 1/4 socket). Remove 4 screws holding Clock/Timer (cross point driver). Peal off plastic front cover from old Clock/Timer and place on new Clock/Timer. Remove electrical connections from old unit and insert on new. Replace all screws and plug range in.
Was this helpful?
Thank you for voting!
Burnt E/CT
3 of 4 people
found this instruction helpful.
-
Luis from SEVIERVILLE, TN
- Really Easy
- 30 - 60 mins
Replaced the old E/CT with the new one.
Was this helpful?
Thank you for voting!
My five-year-old Frigidaire Gas stove was giving an F 10 code.
4 of 7 people
found this instruction helpful.
-
Tracy from Summerville, SC
- Really Easy
- 30 - 60 mins
-
Screw drivers
I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.
Was this helpful?
Thank you for voting!