FEF366DCE Frigidaire Range - Instructions

Used a nut driver to remove old bake element and removed slide on clips on each side took the old pieces to trash and the put new element in by installing slide on electrical connection the tightened up screws with nut driver it was easy and the best thing was ordering of the part and getting the correct part in a timely fashion. I wish all websites were this efficient.

Turned the main power off to my oven. Got my part removed two screws took the old bake element out put the new one in, replaced screws, turned power back on and boom it was fixed. Thanks so much for making it so easy.

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

Removed two screwa holding element in place. Removed the connecting wires. Attached wires to new element. Reset emlement, replaced the screwa and I was done. Actuallt, I did as exactly as indicated in your film discribing the installation. P.S.-Part arrived in two days inspite of the impending hurrican. Extremely satisfied.

My wife had seen a small fire in the bottom right of our oven, and I quickly turned off the oven unit, which put out the fire. We tested the oven a couple more times after it had cooled and determined that indeed the bake element had burned out. I'd used PartSelect before and been very pleased with their service (speed, ease of use of site, etc.,etc.) so I ordered a new bake element, which arrived in two days! It was easy to replace: I turned off the circuit breaker, slid the oven out from the wall, disconnected the plug, and then got to work undoing the tabs that hold the bake element to the rear wall. The only little glitch was that the screw heads on our range were neither slot nor Philips - they turned out to be small square-socket screws. I couldn't see that until I turned a bright flashlight on the job. Then it was a simple matter of trading out the screwdriver bit, disconnecting the old element, plugging in and attaching the new one, and away we went. Oven as good as new! Thanks, PartSelect!

followed the video provided and installed it as instructed. Video and instructions provieded were very helpful

Remove bolt from both ends of element carefully as not to damage wires connected to the ends. Replaced with new element. Simple.

After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!

Turned off electric at breaker box for range. Using a socket wrench from my little pink tool kit, I removed the two screws holding the unit at the back of the oven. Gently pulled each side of the unit out, exposing the terminals. Holding with one hand and wiggling the terminal with the other, removed the element. One was very easy, but the other was harder. Next I connected the new element to the terminals. Gently pushed the terminal back into the oven wall and replace the screws. Last turned the electric back on and then turned the oven on. The video that was online was very helpful.

Thanks to the video on your web site, the replacement was very easy! We had a hard time removing the screws from inside the oven as we did not have a hexnut driver, but once we removed the screws then we lost one of the wires, (it fell back into the little hole) and then we had to remove the back of the oven to get the lost wire, push it through the little hole and we connected the new element, screwed it back in and then we baked some cookies.

My husband said it was easy he just unscrewed the two bolts he was through in no time. Thanks so much. I am so glad my over is working, it had been out for 8 month I am so glad my co-worker told me about you all.

Replaced the bottom element in the oven. Had to remove the 2 screws holding the element in place. Gently pulled the element loose and disconnected it from the wires connected to the oven. Connected new element to the 2 oven wires. Gently pushed the new element into the holes of the oven. Replaced the screws and I was done

Using a socket set, I unscrewed the original/broken heating coil from the back wall of the oven. I gently removed the screws holding the element in place and slid out the connecting wires from inside the oven wall. Then, I detached the wires from the original heating element and attached them to the new one. I slid the wires back into the oven wall, screwed the new element in place making sure both screws were tight, that's it!

Took 2 screws out pulled element forward, unhooked the two clipped on wires. Reattached wires on to new element pushed back into stove put the 2 screws make in, DONE! Really easy cheap fix thank you for the fast shipping and easy to do with video instuctions available item.