FEF358CFSB Frigidaire Range - Instructions

It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!

Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove bakin ... Read more g racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

Removed old elements I stalled new ones

Took screws out back of oven to get to connectors . Pulled old conectors off Installed new element took about 5 min. Very easy job. Also good time to clean oven .

Twisted replacement bulb into place easily. Let there be light!

I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim

I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new elem ... Read more ent and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

My husband followed the video instructions and it was easy to fix.

found your website ,asked the question, got an answer, recieved a diagram and a possible problem diagnosis. obtained the part threw PartSelect quickly. took the knob off unscrewed two screws out ,disconnected the terminals and reconnected to new switch put the two screws back in and put the knob on!!! thanks ncountry "

Ordered new racks and replaced them.

It snapped right into the drawer, was very easy

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the ... Read more computer board, and then the unit worked, with our new element that we replaced!

I first lifted the top of the stove up where the burners are then removed 7 philips head screws plus the 2 screws that hold the latch in place, which is just above the oven door. I pulled the old latch off the rod that goes to the lock motor.I hen put the new latch in and replced all the screws. Turned the self-cleaning cycle on and it w ... Read more orked perfectly.Thanks to the help of repair guy at Parts Select and the pictures made the repair simple and fast. Thank You Patrs Select