All Installation Instructions for Frigidaire Range FEF355DBA

Crack in inner door glass

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

Parts Used:

GLASS

Robert from Richmond, IN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Change on e of the inside glass

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Parts Used:

GLASS

Ronald from Ozone Park, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Oven did not heat after replacing element

First unplug range. Remove 6 screws on back of range( 1/4 socket). Remove 4 screws holding Clock/Timer (cross point driver). Peal off plastic front cover from old Clock/Timer and place on new Clock/Timer. Remove electrical connections from old unit and insert on new. Replace all screws and plug range in.

Parts Used:

Oven Electronic Control Board

Ron from ORLANDO, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Bake Element caught on fire

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

Parts Used:

Oven Bake Element

Judy from Spencerville, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

N/A

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Parts Used:

Infinite Burner Switch - Large Element

Dineshbhai from Rincon HWY21, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

element had been damaged

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Parts Used:

Surface Element - 6 Inch

Merle from Towanda, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Burner not controlable

Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.

Parts Used:

Infinite Burner Switch - Large Element

Royce from KEENE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven bottom panel rusted away

Removed two screws removed and replaced panel.

Parts Used:

Bottom Panel

Ron from CINCINNATI, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Heating element went out

Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test

Parts Used:

Oven Bake Element

ROBERT from MAINEVILLE, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The baking element developed hot spots and stoped working.

I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the baking racks and started the oven to burn off any factory oils on the baking element.

Parts Used:

Oven Bake Element

Jeremiah from Crawfordsville, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Stove was dropped and had broken, bent frame and adjuster feet

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Parts Used:

Leveling Leg Assembly

Paul from PORT ORANGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bake element (bottom of oven) burnt through and snapped in two

Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...

Parts Used:

Oven Bake Element

Amber from CARLISLE, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven element broke

It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!

Parts Used:

Oven Bake Element

Irving from Germantown, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner not heating up.

Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.

Parts Used:

Surface Element - 8 Inch - 220V

Arlene from ERIE, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven door would not close completely.

Instructions couldn't be better or easier. As others have said pre-tap the holes and though it's not a must invest in a #1 square screwdriver bit. The perfect fit will save time on the job.

Parts Used: