Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Element caught fire when i preheated my oven
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.
The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!
Overlay replacement is easy; 1st remove two screws that hold panel to top of stove (philips screwdriver) and lift up off of lip at very top, 2nd remove two screws that hold control to panel (nutdriver or square drive screwdriver), 3rd peel old overlay from control panel face (make sure you get any & all little bits so new overlay sits flush), 4th peel backing from overlay and position over control panel (peel protective film from face of overlay as well), 5th reposition control panel and reinstall two screws removed in step two above, lastly reposition top panel on stove and reinstall the two screws removed in step one above. Drawer glide just snaps into place on the lower rear corners of drawer, then you slide drawer back into place.
Very important first step: Turn off the circuit breaker for the range or disconnect the power cord. I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil element. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.
I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!
The temperature was irratic the entire time the stove was on. I would set it for 350 and it would go up to 425 then down to 275. It was all over the place.
It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com! Jim
I unplugged the stove for precautionary reasons. I then removed the two screws holding element in place with the correct nutdriver. I then carefully pulled out the element and pulled the two female spade connectors off. I then compared to new element and plugged the new element in. Finally I screwed in the new element and tested the oven. It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.
The latch for locking the oven during the self-cleaning cycle was broke and would not lock
I first lifted the top of the stove up where the burners are then removed 7 philips head screws plus the 2 screws that hold the latch in place, which is just above the oven door. I pulled the old latch off the rod that goes to the lock motor.I hen put the new latch in and replced all the screws. Turned the self-cleaning cycle on and it worked perfectly.Thanks to the help of repair guy at Parts Select and the pictures made the repair simple and fast. Thank You Patrs Select