- Home
- FEF352BADF
- Instructions
FEF352BADF Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven baking element burnt into
4 of 5 people
found this instruction helpful.
-
Teresa from Marengo, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great
Was this helpful?
Thank you for voting!
Bottom burner wouldn’t heat
5 of 8 people
found this instruction helpful.
-
cynthia from SEBRING, FL
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Watched the video
Was this helpful?
Thank you for voting!
Old racks had melted plastic on them.
4 of 5 people
found this instruction helpful.
-
James from PAINESVILLE, OH
- Very Easy
- Less than 15 mins
It was a replace racks not repair. No problem
Was this helpful?
Thank you for voting!
Broken door glide
4 of 5 people
found this instruction helpful.
-
Michael from Signal Hill, CA
- Really Easy
- Less than 15 mins
snapped the new piece of plastic in its place and ta da, its fixed.
Other Parts Used:
Was this helpful?
Thank you for voting!
replacing oven racks
4 of 5 people
found this instruction helpful.
-
Lawrence from Elmira, NY
- Really Easy
- Less than 15 mins
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people
found this instruction helpful.
-
Alan from SAN MATEO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Drawer Glide Was Broken
3 of 3 people
found this instruction helpful.
-
Karen from Yuma, AZ
- Very Easy
- Less than 15 mins
Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.
Was this helpful?
Thank you for voting!
the old bake element was corroded and non-funtional
5 of 9 people
found this instruction helpful.
-
Stephen from RONAN, MT
- Really Easy
- Less than 15 mins
-
Screw drivers
Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the
... Read more
oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
3 of 3 people
found this instruction helpful.
-
Kevin from Swanville, ME
- Very Easy
- 15 - 30 mins
-
Screw drivers
Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.
Was this helpful?
Thank you for voting!
Bake element went out
4 of 6 people
found this instruction helpful.
-
Nicholas from COTTONDALE, AL
- Really Easy
- Less than 15 mins
-
Socket set
The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. P
... Read more
ull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.
Read less
Was this helpful?
Thank you for voting!
Cooktop burner was wore out from age
3 of 3 people
found this instruction helpful.
-
John from HAYDEN, AL
- Very Easy
- Less than 15 mins
Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes
Was this helpful?
Thank you for voting!
Cracked glass inside oven door -exposed to heat
4 of 6 people
found this instruction helpful.
-
Marvin from Ventura, CA
- Easy
- 30 - 60 mins
-
Screw drivers
I used good old commom sense to disassemble and reassemble the frame, handle, internal glass,and inter panel to reach and repace the cracked glass. I must admit I had two machine screws left over during reassembly, but found a home. It is important to identify where each and every screw belongs. This will cut down your repair time. I
... Read more
thank PartSelect for providing great service and assisting me in my time of need.
Marv Dixon
Marv Dixon
Read less
Was this helpful?
Thank you for voting!
the indicator light for burners broke and shorted agaist the back panel on range
7 of 15 people
found this instruction helpful.
-
James from Caldwell, ID
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken glass inside door of oven
6 of 12 people
found this instruction helpful.
-
Janice from Brooklyn, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
First took apart oven door. then took out broken glass and replaced with new glass.Put everything back together done.
Was this helpful?
Thank you for voting!
Broiler element burned out
3 of 3 people
found this instruction helpful.
-
Trisha from Shelbyville, TN
- Very Easy
- 30 - 60 mins
-
Screw drivers
Just took the old one out & put the new one in . Just a few screws to remove & put them back when replacing to new broil element , and were back up and cooking :)
Was this helpful?
Thank you for voting!