FEF352AWF Frigidaire Range - Instructions

I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!

Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

pulled out the range and unplugged the range from the outlet! removed the oven racks. unscrewed the heating element and pulled out the wire connections a bit so i could grasp the connectors better and so they would not go back into the holes. getting the bad element off the connectors was the most difficult part of the process - this is what took the longest for me. I used pliers to grab the heating element connector and wiggle until it came loose from the connectors. once off, it was pretty simple to re-connect the replacement element and tuck everything back and screw the element back onto the oven wall. WA-LA!! back in the baking business - kids and mom are happy again! temp needs calibrating, but should be able to figure that out....thanks much!

Just unscrew the two screws that attach element to back of oven. Pull element toward door until you see push on terminals. Pull both terminals off.

purchased correct part from PartSelect and it fit like a glove!

A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

I watched the video on the website and decided even I could attempt this. Went even easier than the video showed. Took less than 3 minutes. Thank you part select!

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

My husband and I pulled the stove away from the wall and unplugged it. We felt it was safer to unplug the stove rather than turn off the breaker. My husband disconnected the baking element and checked the lead wires coming into the oven to see if they were damaged but they were not. He fitted the new baking element to the lead wires and tightened the screws on each side. It was really easy to repair and the video we watched on the internet really helped. As a Mom who bakes a lot, and I wanted to make sure that the oven temp was correct so I tested the temp three different times with my oven thermometer. Each time the oven temp was accurate. Parts Select Service Department was most helpful and I received the part within two days. I highly recommend them and I would use them again.

Husband watched Online Repair Video. Took him maybe 5 minutes to Repair.Thank yall very much.

simple to unscrew the door handle from the inside, remove the broken trim, place new trim on, clamp the door together, then screw the handle back on. Went well!

First observed how the element attached to the oven. Then unplugged the range. Unscrewed it at both ends using my nutdriver. At the connection clips, simply pulled the element end away from the electrical wire it attaches to. Used a pair of pliers to pry loose the clips. Once separated, slightly bent the wire so it would not slip back into the hole that goes into the back of the range. Did this on both sides. Reversed the process to attach the replacement. That process is insert the wires into the connection clips, push the wires back into the range, reattach the element to the oven wall with the original screws, plug in the range. I commend PARTSSELECT for rapid delivery.