EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FEF350BAWC Frigidaire Range - Instructions

All Instructions for the FEF350BAWC
121 - 135 of 932

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element burnt out and cracked
2 of 2 people found this instruction helpful.
  • Robert from LOUISVILLE, KY
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced th e new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!
Was this helpful?
Thank you for voting!
the burner stop working
2 of 2 people found this instruction helpful.
  • Anthony J from HAMMONTON, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Just followed the instructions
Was this helpful?
Thank you for voting!
Oven bake element failed.
2 of 2 people found this instruction helpful.
  • Gerald from PALM COAST, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.
Was this helpful?
Thank you for voting!
oven door not closing completely
2 of 2 people found this instruction helpful.
  • David from BIRDSBORO, PA
  • Very Easy
  • 15 - 30 mins
older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.
Was this helpful?
Thank you for voting!
Broken handle on the lower door
2 of 2 people found this instruction helpful.
  • Robert from Albuquerque, NM
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed the screws holding the element in place. Then I screwed in the new part. No problem at all.
Was this helpful?
Thank you for voting!
Bottom oven element non-functional
2 of 2 people found this instruction helpful.
  • Louis from GAINESVILLE, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal proc edures. Also good time to clean oven.
Was this helpful?
Thank you for voting!
bake element burnt out.
2 of 2 people found this instruction helpful.
  • james from WOOTON, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed screws,unplugged terminal leads,installed new one,back in business.
Was this helpful?
Thank you for voting!
Original terminal degraded and faulty
2 of 2 people found this instruction helpful.
  • Robert from PRAIRIEVILLE, LA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Was this helpful?
Thank you for voting!
bake element burned out
2 of 2 people found this instruction helpful.
  • Kenneth from Wantage, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into b ack wall of oven. Don't know what you would do then.
Was this helpful?
Thank you for voting!
Old heating element broke
2 of 2 people found this instruction helpful.
  • Paul from Ellenville, NY
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated wi th another beer.
Was this helpful?
Thank you for voting!
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
2 of 2 people found this instruction helpful.
  • Nelson from FRUITHURST, AL
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this helpful?
Thank you for voting!
Two burners did not heat
2 of 2 people found this instruction helpful.
  • Conan from Moline, IL
  • Easy
  • 30 - 60 mins
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Was this helpful?
Thank you for voting!
Heavy jam boiler caused elements to sag
2 of 3 people found this instruction helpful.
  • Danny L from CHELAN, WA
  • Really Easy
  • Less than 15 mins
Removed the old & simply inserted the new one
Was this helpful?
Thank you for voting!
Bottom bake element went bad
2 of 3 people found this instruction helpful.
  • James from Martinsburg, WV
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.
Was this helpful?
Thank you for voting!
Oven bake element was dead
2 of 3 people found this instruction helpful.
  • Stephen from Spencer, IN
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.
Was this helpful?
Thank you for voting!
All Instructions for the FEF350BAWC
121 - 135 of 932