EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FEF335BADA Frigidaire Range - Instructions

All Instructions for the FEF335BADA
106 - 120 of 863

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake element (bottom of oven) burnt through and snapped in two
2 of 2 people found this instruction helpful.
  • Amber from CARLISLE, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this helpful?
Thank you for voting!
Broken handle on the lower door
2 of 2 people found this instruction helpful.
  • Robert from Albuquerque, NM
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed the screws holding the element in place. Then I screwed in the new part. No problem at all.
Was this helpful?
Thank you for voting!
Broiler element burnt out. It literally broke off & emitted white-hot sparks.
2 of 2 people found this instruction helpful.
  • MG from ENCINITAS, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
First thing I did was turn off power to the range at the circuit breaker. The repair was generally easy with the exception that 1 screw holding the broiler element support was "welded" into the oven ceiling. I stripped the screw trying to get it out. Fortunately, I had a special tool that allows one to grip the outer edge of the screw w hile turning it --- and that's how I got it apart. Once the broiler element support was off, I removed 2 screws holding the broiler element itself to the oven wall and carefully pulled the broiler element out from the oven wall and detached the wire clips connecting the wires to the broiler element. I reattached the clips onto the new element and installed the new element back into the oven wall. I then reattached the broiler element support using a another screw (because I decimated the original one). I then turned the circuit breaker back on and turned the broiler on. Woila. My broiler works again! Special thanks to the people at this site who were very helpful in seeing to it I got the correct broiler element. The original ordered broiler element was delivered to the wrong address. The folks at this site sent me another one. To make a long story short, they saw to it I got the correct part. I highly recommend this site based on my experience with them.
Was this helpful?
Thank you for voting!
Oven bake element failed.
2 of 2 people found this instruction helpful.
  • Gerald from PALM COAST, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.
Was this helpful?
Thank you for voting!
Element burnt out and cracked
2 of 2 people found this instruction helpful.
  • Robert from LOUISVILLE, KY
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced th e new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!
Was this helpful?
Thank you for voting!
bake element burnt out.
2 of 2 people found this instruction helpful.
  • james from WOOTON, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed screws,unplugged terminal leads,installed new one,back in business.
Was this helpful?
Thank you for voting!
Bottom oven element non-functional
2 of 2 people found this instruction helpful.
  • Louis from GAINESVILLE, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal proc edures. Also good time to clean oven.
Was this helpful?
Thank you for voting!
Old heating element broke
2 of 2 people found this instruction helpful.
  • Paul from Ellenville, NY
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated wi th another beer.
Was this helpful?
Thank you for voting!
Remove broken hinge from oven and replace.
11 of 29 people found this instruction helpful.
  • Robert from Shaker Heights, OH
  • A Bit Difficult
  • More than 2 hours
I looked up the model number of the Tappan oven on the net, found the part on the PartSelect site, ordered it and it arrived within a few days. The disassembly should have required nothing more than a Phillips head screw driver, unfortunately one of the screws was completely frozen and I managed to strip the Phillips head socket.

The screw was in a very awkward position so I first tried using grip pliers on the edge of the screw - this failed, I then tried grinding a flat spot on either side of the screw circumference and using the flats for gripping - it worked but the screw wouldn't move. Finally, I took a hacksaw blade and cut a slot in the head of the screw. I widened the slot using miniature files and finally made the slot wide enough for a large slot blade screwdriver - this worked. After removing that one screw and maneuvering the broken hinge out of the access hole on the stove front (the break in the hinge was such that this took awhile) the rest of the repair went very quickly.

The oven door was such that I could not see all of the hinge and when the part arrived from PartSelect I thought it was the wrong part. I called your parts return number to ask some questions. The lady who took my call was extremely helpful and we first discussed the part ID, then she showed me how to find a picture of the actual part on your site. After looking at the picture and the diagram I suddenly realized the part was correct - it was just that I thought it was supposed to be installed in a different manner. I'm sorry I didn't remember to get her name because she certainly should be commended for he patience and her assistance. Thanks Again.
Was this helpful?
Thank you for voting!
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
2 of 2 people found this instruction helpful.
  • Nelson from FRUITHURST, AL
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this helpful?
Thank you for voting!
bake element burned out
2 of 2 people found this instruction helpful.
  • Kenneth from Wantage, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into b ack wall of oven. Don't know what you would do then.
Was this helpful?
Thank you for voting!
I could can not control the burner
3 of 6 people found this instruction helpful.
  • German from Houston, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
was easy open the back side of the range and change the part, the only issue was the wire I used the diagram
Was this helpful?
Thank you for voting!
Broken right side parts for lower over storage drawer.
2 of 3 people found this instruction helpful.
  • Ty from Baltimore, MD
  • Easy
  • Less than 15 mins
  • Screw drivers
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Was this helpful?
Thank you for voting!
Broken drawer slide
2 of 3 people found this instruction helpful.
  • Michael from Jacksboro, TN
  • Really Easy
  • Less than 15 mins
Remove drawer. Insert new slide. Install drawer.
Was this helpful?
Thank you for voting!
lens was broken
2 of 3 people found this instruction helpful.
  • Kenneth from Coeur d'Alene, ID
  • Really Easy
  • Less than 15 mins
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this helpful?
Thank you for voting!
All Instructions for the FEF335BADA
106 - 120 of 863