FEF326ASH Frigidaire Range - Instructions

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block ... Read more clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Discovered that that oven control panel was to blame for both heating elements to stop working at the same time. Went online and ordered the part which was delivered in 2 days. Installation very basic and included the following: 1)Pulled out stove and un-plugged stove 2)Removed top rear panel 3) Removed 4 screws of the damaged control ... Read more panel (leaving all wires plugged in) 4)Installed new control panel and connected wires one by one to make sure done correctly 5) Replaced rear panel plugged in stove testing oven.

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p ... Read more anel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

It was a replace racks not repair. No problem

my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great

snapped the new piece of plastic in its place and ta da, its fixed.

i used a screwdriver to remove the old drip pans and broken surface element in addition to prepping the bracket for the door. It was extremely difficult for me to find these parts for the frigidaire oven but these fit perfectly! I was extremely pleased with how quick it was to replace or fix everything. I will definitely order again when ... Read more the other surface elements go!

Watched the video

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Removed four srews from bak of the oven so I could get to the timer. Then I unplugged the oven swapped out the wires put everything back together. Plug it back in and started the oven. Work great. Also you must remove the timer faceplate carefully or you will peel off the white.

Removed the backing, removed the old part and disconnected the wires (after taking a quick photo so we knew where to reconnect them on the new part). Removed clock/timer facing and placed on new part. Reconnected the wires to the new part and screwed it back in. Oven now works great without spending the $300 we were quoted by the repai ... Read more r man!!

The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. P ... Read more ull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the ... Read more oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.